Powered By Kitlog Pro v2.0
Eddie's Zodiac XL Project
RV-7
Wings
Work Logs Found:
108
Category Work Time:
315 Hours
Date
Hours
Work Log Summary
Details
02-05-2012
4.00
Nut plates for gap fairings
Details
02-04-2012
5.00
Installed and rigged the flaps
Details
01-08-2012
3.50
Strobes and lenses
Details
01-07-2012
1.50
Left wing,strobes and internal aluminum support do
01-06-2012
3.00
Strobes and internal aluminum support doublers
Details
01-05-2012
3.00
Strobe lenes installed
Details
01-05-2012
1.50
Left wing fiber glass wing tip
01-04-2012
2.00
Right wing tip
Details
12-29-2011
5.00
Right aileron auto pilot servo
Details
07-11-2009
8.00
Fit right flap and move wing to cradle
Details
06-27-2009
6.00
Rivet bottom wing skins
Details
05-30-2009
1.00
Tech councilor inspection right wing
Details
05-30-2009
0.50
Replace two dud rivets with NAS rivets
Details
05-25-2009
3.00
Rivet aileron and flap support bracket
Details
05-25-2009
4.00
Aileron brackets
Details
05-17-2009
0.00
Top wing skins
05-17-2009
6.00
Rivet top wing skins
Details
05-05-2009
0.10
Tank back in place
Details
05-04-2009
2.00
Riveted right wing outboard leading edge
Details
04-20-2009
1.00
Install landing light lens
Details
04-19-2009
3.00
Right wing landing light
04-14-2009
4.00
Install rear fuel tank baffle
Details
04-12-2009
12.00
Proseal Right tank
Details
03-30-2009
2.00
Fuel tank stiffeners, drain and filler
Details
03-29-2009
4.00
Rivet right leading edge skins
Details
03-22-2009
0.00
Fuel fittings
03-22-2009
0.00
Fuel fittings
Details
03-22-2009
6.00
Capacitive fuel senders and tank stiffeners
Details
03-20-2009
1.50
Dimple joint plate and tank skin
Details
03-16-2009
2.50
Test install tank onto wing
Details
03-15-2009
5.00
Z brackets and baffle plate
03-09-2009
3.00
Install joint plate and back drill rib
03-05-2009
2.50
Dimple and etch prime wing skins
Details
03-02-2009
2.50
Wing walk doubler and dimple top skins
Details
02-24-2009
3.00
Rivet ribs to front and rear spar
Details
02-19-2009
1.00
Prepare and etch prime nose ribs
02-18-2009
1.00
Left aileron pins
Details
02-17-2009
1.50
Counter sunk remaining holes in right spar
Details
02-15-2009
2.00
Drill holes in ribs for conduit and etch prime
Details
02-13-2009
2.00
Rivet rear spar
Details
02-12-2009
1.50
Right rear spar
Details
02-09-2009
4.00
Rear spar
Details
02-08-2009
8.00
Tie down bracket
Details
02-01-2009
8.00
Prep right wing spar
01-26-2009
0.00
Left wing complete
01-26-2009
0.00
Install Flap
Details
01-26-2009
6.00
Construct control rods
Details
01-25-2009
5.00
Riveting left flap
Details
01-25-2009
0.00
Rivet left flap part 2
Details
01-15-2009
2.00
Left flap
Details
01-13-2009
2.00
Flap bracket
Details
01-12-2009
2.00
Left Flap
Details
01-11-2009
0.00
Left wing pretty much complete
Details
01-11-2009
9.00
Close the bottom of the wing
Details
01-10-2009
4.00
Left aileron
01-09-2009
4.00
Left Aileron
01-09-2009
0.00
Left aileron
01-08-2009
3.00
Left aileron
Details
01-06-2009
5.00
Fitted outboard leading edge and light
Details
12-23-2008
0.00
Landing light
Details
12-23-2008
5.00
Duckworks Landing Light
Details
12-21-2008
0.50
Drilled hole for Pitot
12-20-2008
0.25
Leak testing tanks
Details
12-20-2008
8.00
Aileron gap seal and flap brace
Details
12-20-2008
0.00
Aileron gap seal and flap brace
12-17-2008
3.00
Aileron Brackets
Details
12-14-2008
4.00
Rivet top skins to left wing
Details
12-13-2008
7.00
Debur, dimple and etch prime
Details
12-10-2008
1.00
Inspection plate installed into left tank
12-09-2008
2.50
Install back plate on left tank
Details
12-06-2008
2.00
Outboard nose skin and ribs dimpled and primed
Details
12-04-2008
1.00
Leading edge joint plate
12-03-2008
2.00
Installed inboard tank rib
Details
11-24-2008
4.00
Installed last 2 outside baffels
Details
11-21-2008
1.50
Install 1 rib into left tank
Details
11-19-2008
2.50
Installed 2 rib into left tank
Details
11-16-2008
3.00
Fuel pick up and vent fitting
Details
11-14-2008
1.00
Installed 1 outboard rib into tank
Details
11-11-2008
1.00
Proseal fuel cap
Details
11-10-2008
3.50
Left fuel tank stiffeners
Details
11-08-2008
5.00
Prepare left fuel tank
Details
11-07-2008
2.00
Prep fuel tank skin and install inspection ring
11-06-2008
1.00
Install capacitive sender
Details
10-30-2008
2.50
Fuel tank attach brackets
Details
10-27-2008
3.00
Fuel tank nose ribs
Details
10-26-2008
2.00
Drill the joint plate for the fuel tank
Details
10-23-2008
3.00
Fuel tank support brackets
Details
10-21-2008
1.20
Tank support brackets
Details
10-19-2008
0.00
Removing the vinyl from the skins
10-19-2008
9.00
Install wing skins
Details
10-19-2008
1.00
Install the leading edge rib and joint strip
Details
10-17-2008
2.20
Level spar and hang top inboard skin
Details
10-15-2008
2.50
Rivet ribs to left spar
Details
10-12-2008
9.00
Back drill and etch prime ribs
Details
10-09-2008
1.00
Installed ribs onto left spar
Details
10-08-2008
1.00
Fluting nose ribs
10-07-2008
3.00
Fluting ribs
Details
10-07-2008
5.00
Edge finishing wing ribs
Details
10-06-2008
0.00
Rivet the doubler brackets
10-06-2008
6.00
Left rear spar preparation
10-06-2008
0.00
Etch priming of the rear spar
10-04-2008
7.00
Left spar nut plates
Details
10-04-2008
0.00
Left spar mounted in jig
10-04-2008
0.00
#6 nut plates riveted and counter sunk
Details
10-03-2008
4.00
Built wing jig
Details
04-03-2008
1.50
Edge finishing ribs
Details
04-01-2008
4.00
Flanging and Fluting W710 ribs
Details
03-31-2008
4.00
Edge finishing ribs
Details
SITE NAVIGATION
Contact Builder
RV-7 Home
Category
# Logs
# Hours
All
470
2573
Ailerons
9
38
Avionics
12
110
Brakes
5
14
Canopy
33
141
Center Fuselage
26
116
Centre spar
3
37
Cowling
20
109
Empennage
65
231
Engine
24
114
Fairing
24
87
Final Assembly
6
39
Firewall
14
66
Flap assembly
6
30
Flight testing
2
25
Front Fuselage
5
115
Fuselage
34
176
FWF
2
16
Instrument panel
9
50
Miscellaneous
10
142
None
4
13
Painting
25
219
Prop
3
7
Rear turtle deck
6
38
Roll Bar
1
16
Rudder
3
3
Seats
2
8
Spinner
3
4
Vertical Stab
5
14
Wheels and brakes
1
41
Wings
108
554
Zodiac 601 XL Home
Copyright © 2001-2024 Matronics. All Rights Reserved.
