KitLog pro

Powered By Kitlog Pro v2.0

Garys RV-7 Builders Log
Work Logs Found: 114
Category Work Time: 187 Hours
 Date
Hours
Work Log Summary

Details

 09-09-2011
0.00
Wing tip attach kit arrived
Details
     

 07-17-2011
0.50
Trimmed flap outboard hinge pins
Details
       

 07-12-2011
2.00
Installed Left flap hinge pin retainer
Details
       

 07-10-2011
3.00
Fabbed hinge pin retainer, installed flap
Details
       

 07-09-2011
1.00
Worked on Right Flap piano hinge
Details
       

 06-29-2011
0.00
Wider flange flap hinge arrived from Vans
Details
     

 06-13-2011
0.50
Deburred R flap brace, top side
Details
     

 06-07-2011
0.50
Removed R flap from wing
Details
       

 06-05-2011
1.50
Mounted R wing flap.
Details
       

 06-04-2011
1.50
Mounted R wing aileron
Details
       

 06-01-2011
1.00
Swapped wings between cradle and bench
Details
       

 05-31-2011
1.00
Installed pitot tubing to bay location
Details
       

 05-29-2011
2.50
Mounted pitot tube mount
Details
       

 05-26-2011
1.50
Clecoed L wing bottom skins and match drilled to h
Details
       

 05-23-2011
1.00
Matched drilled L flap hinge to flap brace
Details
       

 05-22-2011
1.50
Adjusted L aileron push rods and torqued
Details
       

 05-21-2011
0.00
Vans order arrived. W-730 jig, rod end bearing, pa
Details
     

 05-21-2011
2.00
Mounted L aileron
Details
       

 05-19-2011
1.00
Fabbed bushing spacers for ailerons
Details
     

 05-16-2011
1.00
Took L wing out of cradle and set on bench.
Details
       

 05-15-2011
2.50
Fabbed W-818 push tubes
Details
       

 05-13-2011
1.00
Assembled aileron push tubes
Details
       

 05-12-2011
1.50
Cleaned and Primed aileron push rod parts
Details
       

 05-11-2011
0.50
Finished deburring aileron push rod parts
Details
     

 05-08-2011
0.50
Did a little deburring on threaded rod ends
Details

 05-07-2011
1.00
Drilled #30 push rod tube holes
Details
       

 05-05-2011
1.00
Started fabbing aileron push rods
Details
       

 05-02-2011
0.00
Flap parts from Vans arrived
Details
       

 05-01-2011
5.00
Finished Left Flap, both flaps now complete.
Details
       

 04-30-2011
4.00
Completed right flap
Details
       

 04-26-2011
3.00
Started riveting the right flap
Details
       

 04-25-2011
1.00
Cleaned and primed R flap parts.
Details
       

 04-24-2011
1.50
Dimpled all R flap parts.
Details
       

 04-23-2011
4.00
Almost finished L flap, started R flap prep.
Details
       

 04-22-2011
2.00
Dimpling and riveting L flap
Details
       

 04-17-2011
3.00
Dimpled, cleaned, primed L flap parts.
Details
       

 04-16-2011
2.50
R flap skin prep and 706A fab.
Details
       

 04-15-2011
2.00
Fitted skins and hinge for left flap
Details
       

 04-13-2011
1.00
Match drilled bottom flap skins to ribs
Details
       

 04-10-2011
1.50
Clecoed flap skeletons together
Details
       

 04-09-2011
3.00
Started making the flaps
Details
       

 04-08-2011
1.00
Completed Ailerons!
Details
       

 04-07-2011
1.00
Worked on Aileron leading edge
Details
       

 04-06-2011
2.50
Finished riveting aileron top skins to spar
Details
       

 04-04-2011
2.00
Started riveting ailerons
Details
       

 04-03-2011
1.50
Primed aileron parts.
Details
       

 03-31-2011
0.50
Dimpled and deburred aileron parts
Details

 03-28-2011
1.25
Almost finished dimpling aileron parts.
Details
       

 03-27-2011
4.00
Match drilled and deburred aileron parts
Details
       

 03-22-2011
0.75
Match drilled aileron #30 holes
Details
       

 03-21-2011
1.50
Prepped aileron skeletons
Details
       

 03-20-2011
2.00
Aileron bracket prep
Details
       

 03-13-2011
2.50
Back riveted aileron stiffeners, bent skins
Details
       

 03-11-2011
1.50
Primed Ailerons
Details
       

 03-10-2011
1.00
Prepped ailerons
Details
     

 03-07-2011
3.00
Started on the ailerons
Details
       

 03-06-2011
1.50
Aileron stiffeners
Details
       

 03-05-2011
2.50
Flap braces
Details
       

 03-04-2011
1.50
Riveted aileron gap seals
Details
       

 02-28-2011
1.00
Primed Aileron gap seals
Details
     

 02-27-2011
3.00
Riveted aileron brackets on wing rear spar
Details
       

 02-21-2011
1.50
Started riveting aileron brackets.
Details
       

 02-20-2011
3.00
Primed and riveted aileron brackets.
Details
       

 02-19-2011
1.50
Prepped aileron brackets
Details
     

 02-12-2011
0.00
Mark T picked up wing jig today
Details

 02-11-2011
1.00
Put wings in cradle and tore down wing jig
Details
     

 02-05-2011
3.00
Built the cradle for the wings.
Details
       

 01-31-2011
1.00
Prepped bottom skins
Details
       

 01-24-2011
1.00
Installed R wing conduit hangers
Details

 01-21-2011
1.00
Pitot (pee-toe) bracket
Details
       

 01-17-2011
3.50
Completed top skins on R wing
Details
       

 01-16-2011
2.00
Finished L wing top skins, started on R wing
Details
       

 01-13-2011
1.50
Misc wing stuff
Details
       

 01-09-2011
2.50
L wing top skin riveting
Details
       

 01-08-2011
2.00
Riveted L wing top skins.
Details
       

 01-07-2011
0.75
Torqued R tank attach screws
Details
     

 01-06-2011
1.00
Installed wing tank screws to spar
Details
       

 01-02-2011
0.10
Torqued some tank attach bolts
Details
       

 01-01-2011
2.00
Started bolting on tanks.
Details
       

 12-31-2010
15.00
Tank Work
Details
     

 12-30-2010
1.50
R Leading Edge Riveting and R Tank
Details
       

 12-29-2010
1.00
R Leading Edge Riveting
Details
       

 12-28-2010
1.50
R Leading Edge Riveting
Details
       

 12-22-2010
2.00
Finished L leading edge riveting
Details
       

 12-19-2010
1.50
Finished riveting L leading edge rib rivets.
Details
       

 12-12-2010
2.00
Aileron Bell Crank install
Details
       

 12-05-2010
1.50
Started riveting leading edge to main spar
Details
       

 11-24-2010
1.50
Leak tested fuel tanks
Details
       

 11-24-2010
1.00
Installed some hangers for wing conduit.
Details
       

 11-17-2010
0.00
Bought pipe hangers for wing conduit
Details
     

 10-31-2010
2.00
Sealed tank end plates
Details
       

 10-30-2010
1.50
Safety wired fuel pick up tubes
Details
       

 10-29-2010
0.00
Proseal, tank test kit, bolt and nut drill jigs ar
Details
     

 10-24-2010
2.00
Mounted fuel pick up tubes and torqued
Details
     

 10-23-2010
0.50
Worked on fuel level floats
Details
       

 10-18-2010
0.50
Sent pics to Vans of wallowed out hole.
Details
       

 10-17-2010
3.50
Installed conduit, AOA and Pitot tubing
Details
       

 10-16-2010
0.00
Visited local RV-6A builder, Jim B
Details
     

 10-15-2010
0.00
Tubing kits and misc tools from Avery arrived
Details
       

 09-19-2010
0.75
Mounted the Dynon roll servo bracket in right wing
Details
       

 09-12-2010
1.00
Colten finished the spare light lens
Details
       

 09-11-2010
3.00
Finished L Wing Landing Light Lens Install
Details
       

 09-11-2010
0.00
Dynon Autopilot Roll Servo arrived from Avery.
Details
       

 09-06-2010
3.50
Installed mount and lens in right wing
Details
       

 09-05-2010
1.00
Installed nutplates on L wing light mount
Details
     

 08-29-2010
0.00
Hardware kits arrived from Duckworks
Details
     

 08-27-2010
1.00
Cut hole in left leading edge
Details
       

 08-23-2010
1.00
Continued on L wing landing light mount
Details
       

 08-22-2010
2.00
Started Left landing light mount installation
Details
       

 08-07-2010
1.00
Clecoed Left inboard skin
Details
       

 07-12-2010
1.00
Installed conduit in L wing
Details
       

 03-12-2010
1.00
Mounted parts drawers, removed tank and leading ed
Details
       

 09-19-2009
4.00
Constructed wings stands and mounted spars
Details
       

 09-12-2009
0.00
Purchased partially completed wing kit
Details
       










Copyright © 2001-2024 Matronics. All Rights Reserved.