KitLog pro

Powered By Kitlog Pro v2.0

JIM'S WEB SITE
RV-12  
  Finish Kit
77 Logs Found 
First Photo
 Date

 Work Log Summary
01-20-2010
 Finish strip around wing
Getting ready to start the engine for the 1st time.
 01-19-2010
 First Engine Run-up

01-15-2010
 Interior install

01-01-2010
 Reinstalled Canopy
12-31-2009
 Upper panel skin installed
12-30-2009
 Bleed brakes
12-08-2009
 Interior

11-12-2009
 Rear Window
Added ProSeal where it connects to the turtle skin.
 11-11-2009
 Fuel Tank
11-10-2009
 Fuel Tank install
11-09-2009
 Fuel tank
Pressurized tank with 1 psi and checked for leaks.
 11-08-2009
 Fuel Tank leak test
11-05-2009
 Misc
11-04-2009
 misc panels
11-03-2009
 Rudder cable tunnel cover
Lap belts and flooring installed.
 11-02-2009
 Seat Belts

11-01-2009
 Fuel Tank
10-31-2009
 Fuel tank
10-30-2009
 Fuel Tank
10-29-2009
 Fuel Tank
09-22-2009
 Fuel Tank
Mounted the fuel fill nozzle cap.
 09-21-2009
 Fuel Tank

09-15-2009
 Canopy Latch revision

08-24-2009
 Cowling

08-21-2009
 Canopy
Bottom Cowling in place and installing side hinge.
 08-20-2009
 Installing Cowling
Riveting the side hindge to the lower cowling.
 08-20-2009
 Cowling
Trimming the upper cowl with dremal tool disk.
 08-12-2009
 Cowling
08-11-2009
 Cowling
Nose wheel attached and tension adjusted to 26 lbs.
 08-10-2009
 Brake lines

08-09-2009
 Nose wheel
Left main gear with wheel attached.
 08-07-2009
 Mounted main wheels and nose gear.
Ben packing main gear bearings.
 08-05-2009
 Main Landing Gear
Main gear tire and wheel
 08-04-2009
 Tire Mounting
Nose wheel and tire.
 08-03-2009
 Tire Mounting
Ben helped with installing and removing the canopy until we got it right.
 07-22-2009
 Attaching the canopy
Fiberglass after it was removed from the fuselage.
 07-10-2009
 Triming Canopy
07-09-2009
 Canopy
07-08-2009
 Canopy sanding
07-07-2009
 Sanding Canopy
Still sanding.
 07-06-2009
 Canopy

07-05-2009
 Canopy sanding
Adding another layer of glass.
 07-04-2009
 Canopy
Adding glass to the sides.
 07-03-2009
 Canopy
Sanded down the foam blocks to shape of the fuselage sides.
 07-02-2009
 Canopy
Sanded the side canopy arms in prep for the foam to be attached.
 06-30-2009
 Canopy
Tapped the roll bar to install the guide blocks.
 06-29-2009
 Canopy
Clecoed canopy to frame.
 06-28-2009
 Canopy
Primed and painted canopy frame.
 06-26-2009
 Canopy
06-25-2009
 Canopy
Ben sat inside to help while drilling thru side skirts.
 06-24-2009
 Canopy
Drilling canopy into front frame.
 06-23-2009
 Canopy
Trimming the rear edge of canopy.
 06-22-2009
 Canopy

06-17-2009
 Canopy

06-16-2009
 Canopy
Clamped roll bar with spacers.
 06-15-2009
 Canopy
06-12-2009
 Canopy
06-11-2009
 Flight Controls
Both rudder cables running back to rudder.
 06-09-2009
 Flight controls
Flaperon control handle in place with temp shims.
 06-08-2009
 Flight controls
Connected Flaperon mixer control.
 06-07-2009
 Flight controls
Connected Flaperon mixer control.
 06-06-2009
 Flight controls
Drilled and tapped the roll bar for the rear window.
 06-04-2009
 Electrical
New seats arrived today.
 05-27-2009
 Seats arrived today
Mixing ProSeal to use on the Fuel Tank.
 05-26-2009
 Fuel Tank
Painted the Flaperon control handle. Also made up some of the control rods and parts.
 05-25-2009
 Flight controls

05-20-2009
 Fuel Tank
Cleaned parts of the Fuel Tank.
 05-19-2009
 Fuel Tank
Installed rudder pedals and routed the wires.
 05-18-2009
 Electrical
05-15-2009
 Electrical
05-14-2009
 Electrical
Ran wires to the fuselage pin switch.
 05-13-2009
 Electrical

05-12-2009
 Electrical
05-11-2009
 Electrical
Side fuselage cover.
 05-09-2009
 Fuselage wiring
04-29-2009
 organizing parts from inventory
04-28-2009
 Inventory Finish Kit



SITE NAVIGATION

Contact Builder

RV-12 Home

 All

 Avionics

 Empennage

 Engine

 Finish Kit

 Flying

 Fuselage

 Inventory

 Miscellaneous

 Ordering supplies

 Paint & Finish

 Plan Review

 Shop Supplies

 Wings









Copyright © 2001-2010 Matronics. All Rights Reserved.