KitLog pro

Powered By Kitlog Pro v2.0

Bobs RV7 Site
Work Logs Found: 74
Category Work Time: 241 Hours
 Date
Hours
Work Log Summary

Details

 02-02-2013
3.60
Electronic Ignition Troubleshooting
Details
       

 12-03-2012
3.00
Safety Wire Worm Clips
Details
       

 10-04-2011
3.70
Starter Test
Details
       

 07-23-2009
2.00
Prop Installed and safety wired
Details
       

 07-23-2009
1.00
Installed air intake
Details
       

 07-11-2009
1.50
Wiring bundles
Details
       

 06-08-2009
3.80
Engine wiring - firewall access points
Details
       

 05-20-2009
4.30
Engine wiring - wiring bundles
Details
       

 05-19-2009
3.70
Engine wiring - Lightspeed ignition
Details
       

 05-11-2009
2.60
Engine wiring - firewall pass-throughs
Details
       

 04-30-2009
4.90
Engine wiring - right side, starter
Details
       

 04-14-2009
2.90
Engine wiring - magneto
Details
       

 03-24-2009
3.30
Engine wiring - alternator
Details
       

 03-11-2009
3.00
Engine wiring - left side
Details
       

 02-28-2009
2.00
Wiring run from engine to firewall
Details
       

 02-27-2009
2.00
Engine wiring
Details
       

 02-27-2009
2.00
Engine wiring
Details
       

 02-26-2009
2.50
Installed cooling hoses
Details
       

 02-24-2009
1.30
Oil Cooler installed
Details
       

 02-14-2009
2.20
Hose connections, dipstick, heat hose
Details
       

 02-12-2009
2.00
Sniffle valve
Details
       

 01-30-2009
2.50
Oil breather tube
Details
       

 01-30-2009
1.70
Fuel pump overflow
Details
       

 01-29-2009
2.50
Riveted cowling to fuselage hinge
Details
       

 01-28-2009
2.00
Cowl to Fuselage hinge
Details
       

 01-27-2009
2.00
Firesleeve throttle cable
Details
       

 07-09-2008
4.00
Baffle seal templates
Details
       

 07-08-2008
3.00
Various cooling holes in baffleing
Details
       

 07-07-2008
3.50
Secure fuel lines and heat hose
Details
       

 06-18-2008
1.50
Revise Baffle Fuel Line Hole
Details
       

 06-04-2008
2.00
Fuel lines and baffel pass throughs
Details
       

 06-03-2008
1.00
Installed and ran heater hose
Details
       

 06-03-2008
1.30
Heater hose
Details
       

 06-02-2008
2.40
Heater hose in forward baffel floor
Details
       

 05-22-2008
3.00
Prop oil line
Details
       

 05-21-2008
4.30
OAT sensor and wiring run
Details
       

 05-20-2008
1.10
Oil and fuel pressure sensors
Details
       

 05-19-2008
4.20
CHT, EGT and plug wires
Details
       

 05-16-2008
3.00
Electronic ignition wiring
Details
       

 05-15-2008
2.60
Electronic ignition module
Details
       

 05-14-2008
5.50
Alternate air intake
Details
       

 05-13-2008
3.50
Purge valve cable
Details
       

 02-01-2008
6.50
Alternate air
Details
       

 01-31-2008
3.90
Alternate air
Details
       

 01-29-2008
5.50
Alternate air source
Details
       

 10-23-2006
5.00
Spinner Fit, Top Cowl Hinge
Details
       

 10-22-2006
1.50
Prop Spinner
Details
       

 10-22-2006
4.50
Installed Prop
Details
       

 10-21-2006
4.00
Prop Spinner Bulkhead
Details
       

 09-02-2006
2.50
Installed the magneto cap and wires.
Details
     

 08-31-2006
5.00
Mounted Exhaust System
Details
       

 08-30-2006
3.50
Electronic Ignition Mount
Details
       

 08-10-2006
5.50
Electronic Ignition module mounted
Details
       

 08-09-2006
2.00
Planning electronic ignition installation.
Details
     

 08-07-2006
3.50
Engine control cables
Details
       

 07-09-2006
3.00
Connected manifold pressure lines.
Details
       

 07-08-2006
5.50
Installed throttle and mixture cable brackets. Se
Details
       

 07-07-2006
5.00
Modify throttle and mixture control cable supports
Details
       

 07-06-2006
6.00
Cut firewall holes for engine control cables
Details
       

 07-05-2006
2.00
Installed support brackets for engine control cabl
Details
       

 07-05-2006
3.00
Installed prop governor and control brackets
Details
       

 07-03-2006
4.50
Engine controls
Details
       

 03-17-2006
4.00
Brakes, engine controls planning
Details
       

 03-16-2006
6.00
Alternator
Details
       

 03-15-2006
2.00
Manifold pressure transducer and line.
Details
       

 03-15-2006
1.80
Breather tube, oil dipstick
Details
       

 03-14-2006
4.60
Oil and fuel pressure sensors
Details
       

 03-13-2006
2.00
Oil temp, RPM sensors
Details
       

 03-13-2006
3.00
CHT and various lines
Details
       

 02-21-2006
2.00
Installed engine mount
Details
     

 10-11-2005
3.00
Replaced the Heat Valve on Firewall
Details
       

 08-30-2004
7.00
Mounted Soledoids to the Firewall
Details
       

 08-29-2004
6.20
Installed the battery box
Details
       

 04-23-2004
3.50
Drilled Engine Mount
Details
       










Copyright © 2001-2024 Matronics. All Rights Reserved.