KitLog pro

Powered By Kitlog Pro v2.0

Bill & Brendas RV-8 QB
Work Logs Found: 64
Category Work Time: 162 Hours
 Date
Hours
Work Log Summary

Details

 10-12-2014
1.00
Removed some scratches from the aft end of the can
Details

 07-13-2014
2.50
Wet sand scuff marks from outer edge of windscreen
Details

 07-09-2014
1.00
Mask off the scratched area around the windscreen
Details

 07-06-2014
3.00
Feather in the windscreen fairing and radius sandi
Details
     

 07-02-2014
2.00
peel off tape suronding the windscreen
Details
       

 07-01-2014
1.50
windscreen pure epoxy applied
Details
       

 06-30-2014
2.00
Install pop rivits into the windscreen fairing
Details
       

 06-27-2014
2.00
Sand primer on windscreen fairing-1
Details
       

 06-26-2014
1.50
sand windscreen inside corners and under aft lip
Details

 06-25-2014
1.25
Sand a taper edge on aft upper fairing and misc
Details
       

 06-22-2014
2.25
windscreen upper fairing aft edge final cut to fit
Details
       

 06-18-2014
5.50
windscreen faiting sanding-8
Details
       

 06-17-2014
5.00
windscreen fariing sanding 7
Details
       

 06-13-2014
2.50
Windscreen fairing sanding-6
Details
     

 06-04-2014
2.50
windscren fairing sanding-5
Details
       

 06-03-2014
2.50
windscreen fairing sanding -4
Details
     

 05-30-2014
1.50
Windscreen fairing sanding-3
Details
     

 05-29-2014
5.00
windscreen fairing sanding-2
Details
       

 05-25-2014
4.50
windscreen fairing sanding -1
Details
       

 05-24-2014
2.00
windscreen fairing 4...cake icing
Details
     

 05-21-2014
2.50
Windscreen fairing-3
Details
       

 05-21-2014
0.75
Canopy skirt sanding left side
Details

 05-20-2014
3.00
windscreen fairing-2
Details
       

 05-19-2014
4.50
windscreen fairing-1
Details
       

 05-16-2014
5.00
windscreen5-final screws install, gap sanding, mas
Details
       

 05-15-2014
5.00
Windscreen-4 masking off and prep for fairing
Details
       

 05-14-2014
0.50
widscreen -3
Details

 05-12-2014
3.50
windscreen fitting -2
Details
       

 05-11-2014
2.50
Fitting windscreen to canopy and rollbar-1
Details
       

 08-23-2013
0.75
Redo two rivits in front canopy bow and spacer
Details
     

 08-22-2013
1.50
Prep and rivit the canopy front bow
Details
       

 08-19-2013
2.00
Rivit canopy and canopy skirt to frame
Details
       

 08-18-2013
2.25
canopy removal and prep to receive skirts
Details
       

 08-15-2013
1.25
Canopy handle and latch lever trim
Details
       

 08-12-2013
1.50
Drill Canoopy frame rollers and install canopy sto
Details
       

 08-12-2013
0.00
canopy stop drilling
Details
       

 08-11-2013
0.75
Mid position canopy stop
Details
       

 08-10-2012
1.50
skirts-12 (aprox) and trim canopy front edge again
Details
       

 07-02-2012
3.00
Canopy skirt left side drilling-2
Details
       

 07-01-2012
1.50
Canopy left side skirt drilling-1
Details
       

 06-30-2012
3.75
Skirt templates and initial fitting left side
Details
       

 06-19-2012
4.00
Final drilling of canopy and frame- Temp attach ca
Details
       

 06-18-2012
5.00
canopy bottom edge final cut and polish, Frame dri
Details
       

 06-16-2012
0.60
Canopy misc.
Details

 06-14-2012
5.50
Drill canopy to frame-1
Details
       

 06-11-2012
4.00
Fit and trim canopy to frame and aft bow-1
Details
       

 06-10-2012
3.00
Canopy cut session 5-The Big Cut!
Details
       

 06-09-2012
3.50
canopy cut and fit -4
Details
       

 06-04-2012
0.50
dwg 44 detail A and chapter 9-2
Details
       

 06-04-2012
1.75
Canopy cutting-3 and trim the front skin for clear
Details
       

 05-30-2012
5.00
Canopy cutting-2
Details
       

 05-27-2012
3.00
canopy cutting-1
Details
       

 05-26-2012
2.50
Drill anchor block to F807. Prep for canopy cuttin
Details
       

 01-07-2012
2.50
Finish slider block and drill fwd most screw hole
Details
       

 01-05-2012
1.50
Canopy center rail slider block redo
Details
       

 01-02-2012
4.00
Canopy side rails-final drilling
Details
       

 12-30-2011
3.50
Canopy frame fitting and drill side rails
Details
       

 12-25-2011
1.50
canopy frame bending-1
Details
       

 12-24-2011
1.50
Canopy center slide block fitted and drilled-1
Details
       

 12-24-2011
3.00
canopy center rail final, fit side rails
Details
       

 12-22-2011
2.00
center slide rail-4
Details
       

 12-18-2011
0.50
canopy slide-3
Details
     

 12-17-2011
0.75
canopy slide-2
Details

 12-16-2011
5.00
Canopy slide spacer and cap 1
Details
       










Copyright © 2001-2024 Matronics. All Rights Reserved.