Powered By Kitlog Pro v2.0
Dave White RV-7 Build Site
RV-7
Empennage
Work Logs Found:
115
Category Work Time:
249 Hours
Date
Hours
Work Log Summary
Details
07-20-2014
1.50
Perfecting trim tab actuation
Details
07-20-2014
1.50
End-to-endtesting of the trim tab servo
Details
07-19-2014
1.00
Test fitting the trim tab servo
Details
07-19-2014
1.00
Riveting the right elevator
Details
07-19-2014
3.00
Aligning the trim tab
Details
07-18-2014
4.00
Riveting the left elevator
Details
07-17-2014
1.00
Left elevator
Details
07-06-2014
1.00
Left elevator - less than perfect
Details
07-05-2014
2.50
Left elevator - close up trim tab recess
Details
06-29-2014
2.00
Trim tab construction
Details
06-28-2014
2.00
Bending trim tab ends - Take 2
Details
10-27-2013
1.00
Bending the trim tab ends
Details
10-18-2013
0.75
Trim tab, and "oops"
Details
10-07-2013
1.50
Rivet LH elevator skeleton
Details
10-05-2013
1.00
Completed servo plate, cut trim tab horns
Details
09-27-2013
0.75
Installed 'Z' section servo supports
Details
09-14-2013
2.00
Drilling out and re-riveting elevator spar
Details
09-09-2013
2.00
Riveting the RH elevator skeleton. Or not...
Details
09-08-2013
1.00
Countersinking RH elevator spar
Details
09-07-2013
4.00
Prep'ing LH elevator skin & skeleton
Details
09-06-2013
2.00
Completed back-riveting LH elevator skin
Details
09-05-2013
2.00
Began riveting LH elevator skin
Details
09-04-2013
1.00
Tried different primer.
Details
09-02-2013
1.00
Began priming LH elevator. Maybe...
Details
09-01-2013
7.00
Starting the LH elevator
Details
08-31-2013
1.50
Fixing yesterday's error
Details
08-30-2013
4.00
Counterweight / Rivetting the RH elevator
Details
08-30-2013
0.50
Bending the RH elevator skin
Details
08-24-2013
5.50
Riveting the RH elevator skeleton
Details
08-23-2013
2.50
Primed Right Elevator parts
Details
01-08-2012
2.00
Remove Alclad from RH elevator parts
Details
01-08-2012
2.00
Complete dimpling RH skin with pop rivet dimpler
Details
01-07-2012
2.50
Dimple RH Elevator skeleton & skin
Details
01-02-2012
1.00
RH elevator counterweight
Details
01-02-2012
3.50
RH Elevator - drill skin to skeleton
Details
01-01-2012
2.00
RH elevator - skeleton
Details
12-24-2011
2.00
Drill stiffeners to RH elevator skin
Details
12-23-2011
2.50
Left Elevator - stiffeners
Details
12-22-2011
2.50
Right Elevator - stiffeners
Details
05-31-2011
5.50
Rolled the Rudder Leading Edge - *eventually*...
Details
05-19-2011
0.25
Edge rolled rudder leading edge skin
Details
05-17-2011
2.50
Double flush riveted Rudder TE
Details
05-08-2011
0.50
Apply adhesive to rudder trailing edge wedge
Details
05-07-2011
2.00
Rivet rudder skin to structure
Details
05-06-2011
1.50
Rivet upper rudder skin to structure
Details
05-05-2011
1.50
Re-riveted rudder structure (correctly!)
Details
05-04-2011
1.50
Correcting carelessness - a lesson learned
Details
05-01-2011
3.75
Rivetted rudder structure
Details
04-25-2011
0.75
Finished priming rudder
Details
04-24-2011
3.25
Priming - still not cracked it :-(
Details
04-19-2011
2.00
Drilling rudder counterbalance weight & priming
Details
04-17-2011
6.00
Back in the saddle - Continuing with the rudder
Details
08-24-2010
1.50
Match drilled rudder TE & c/sunk TE wedge
Details
07-24-2010
1.00
Beginning to prepare rudder trailing edge
Details
07-19-2010
0.50
Fabricating the lower rudder reinforcement strips
Details
07-17-2010
3.50
More work on rudder skeleton
Details
07-16-2010
2.50
Completed back-riveting stiffeners to rudder skins
Details
07-15-2010
2.00
Began back-riveting stiffeners to RH rudder skin
Details
07-14-2010
0.75
Completed priming rudder parts
Details
07-13-2010
2.00
Primed rudder stiffeners and skins
Details
07-11-2010
0.50
Rudder counterweight fairing - initial assembly
Details
07-10-2010
2.00
Completed dimpling and deburring stiffeners/skins
Details
07-09-2010
2.00
Completed deburring & dimpling stiffeners and skin
Details
07-08-2010
2.00
Deburr stiffeners & debur/dimple RH rudder skin
Details
07-07-2010
2.00
Match drilled skins & stiffeners
Details
07-06-2010
2.00
Assemble and check fit rudder
Details
07-05-2010
2.50
Match drilled rudder skins & stiffeners
Details
07-04-2010
4.00
Prepared rudder stiffeners
Details
07-02-2010
4.00
Completed rivettinng of Horizontal Stab
Details
07-01-2010
2.50
Rivetted RH stabiliator skin & structure
Details
06-30-2010
2.50
Correcting significant rivet error
Details
05-30-2010
3.00
Inventory wing kit
Details
05-02-2010
3.00
Empennage fwd spar and inner ribs rivetting
05-01-2010
2.00
Empennage skeleton aft spar rivetting
04-29-2010
0.75
RH Empennage skin priming
04-25-2010
5.50
Rivetted HS rear spar
Details
04-21-2010
1.00
Priming & more prep
Details
04-20-2010
1.50
More primer prep - RH Horiz Stab
04-19-2010
1.00
Confirmed priming technique...
Details
04-18-2010
1.50
Yet more priming improvements
Details
04-17-2010
1.50
Solving primer problems
Details
04-14-2010
2.00
Sprayed primer on LH Horizontal stab
Details
04-08-2010
2.00
Completed Vertical Stabiliser
Details
04-07-2010
1.00
VS forward spar to ribs - rivet error & solution
Details
04-04-2010
2.50
Rivetted one side of VS skin
04-03-2010
2.50
Rivetting remainder of VS skeleton
Details
04-02-2010
3.50
First rivetting - Vertical Stab rear spar
Details
02-21-2010
3.00
First attempt at spraying primer
Details
01-10-2010
1.00
Prepared VS skeleton for spraying
Details
12-30-2009
1.00
Countersunk vertical stabiliser stiffener
Details
12-25-2009
1.75
Dimpled VS skeleton and (most of) VS skin
Details
12-24-2009
1.00
Deburring vertical stabiliser skin
Details
12-22-2009
1.50
Dimpled RH Horizontal Stabiliser skin
Details
12-20-2009
2.50
Completed dimpling Horizontal Stabiliser understru
Details
12-19-2009
1.00
Dimpled LH Horiz Stabiliser Skin
Details
12-13-2009
3.00
Began dimpling HS sub-structure
Details
12-12-2009
4.00
Replacement Left HS fwd spar
Details
12-04-2009
0.00
Replacement LH HS fwd spar arrives
Details
11-28-2009
4.50
Vertical stabiliser prep and initial assy
Details
11-26-2009
4.50
Prepared right hand side of HS & assembled full st
Details
11-25-2009
0.00
Response from Van's on edge distance issue
Details
11-22-2009
5.00
Inspect port HS; repeat process for stbd HS assemb
Details
11-21-2009
4.50
Drilled port Horizontal stabliser structure
Details
11-20-2009
2.50
Cleco'd skin to port Horizontal Stabilizer
Details
11-19-2009
1.00
Countersunk & Dimpled HS fwd spar
Details
11-17-2009
0.50
Full check-assembled HS forward and rear spars
Details
11-17-2009
1.50
Bend HS Fwd Spar web 6 deg
Details
11-14-2009
2.00
HS Forward spar bend relief (LH)
Details
11-13-2009
2.00
Cut HS404 rib flanges & check fit assy
Details
11-09-2009
0.50
Began to bend HS fwd spar reinforcing bars
Details
11-08-2009
4.00
Shaped HS Forward Spar reinforcing bars
Details
11-07-2009
4.00
Completed drilling / deburring rear spar
Details
11-06-2009
2.50
Rear spar - drill out #30 holes & cleco hinges
10-31-2009
2.00
Prepared HS rear spar reinforcement
Details
10-20-2009
2.00
Empennage kit arrived & inventoried
SITE NAVIGATION
Contact Builder
RV-7 Home
Category
# Logs
# Hours
All
170
303
Empennage
115
249
Miscellaneous
8
2
Shop Supplies
7
3
Tools
6
Wings
27
46
Workshop & Supplies
7
3
Copyright © 2001-2024 Matronics. All Rights Reserved.
