KitLog pro

Powered By Kitlog Pro v2.0

Dan's Web Site
Work Logs Found: 39
Category Work Time: 47 Hours
 Date
Hours
Work Log Summary

Details

 03-30-2007
2.00
Install Parking Brake, Carb Heat, Throttle, Mixtur
Details
       

 03-30-2007
1.00
Install Panel and Vents Permanently
Details
       

 03-30-2007
1.00
Drill and Install Bracket for Engine Control Cable
Details
       

 03-29-2007
1.50
Drill/Dremel Holes in Subpanel for Harnesses/Cable
Details
     

 03-28-2007
1.50
Temporarily Install Panel; Mark Subpanel for Cutou
Details
       

 03-28-2007
3.00
Drill/Dremel Holes in Subpanel for Harnesses/Cable
Details
       

 03-13-2007
0.50
Install Dimmer Switch Knob
Details
     

 02-06-2007
3.00
Wet Sand/Polish Panel, Install Instruments
Details
       

 02-06-2007
3.00
Wet Sand/Polish Panel, Install Instruments
Details
       

 07-31-2006
1.00
Sand/Clean Panel to Prime Again - Gray This Time
Details
       

 07-31-2006
0.50
Prime Panel Using Gray Epoxy Primer
Details
       

 07-24-2006
1.00
Sand/Acetone Panel and Covers for Priming
Details
     

 07-24-2006
1.00
Prime Panel with White Epoxy Primer
Details
       

 07-24-2006
0.50
Inspect Priming
Details
       

 07-22-2006
2.00
Create Anti-Rotation Ring for Ignition Switch
Details
       

 07-15-2006
1.00
Drill Holes for Toggle Switches
Details
       

 07-15-2006
1.00
Debur/Edge Prep Anti-Rotation Strips/Panel for Swi
Details
       

 07-15-2006
1.00
Acetone/Alodine/Rivet Anti-Rotation Strips to Pane
Details
       

 07-07-2006
1.00
Drill Holes for Cabin Heat & Parking Brake Cables
Details
       

 07-07-2006
1.00
Drill Hole for Low Voltage Light; Trim Bracket
Details
       

 07-06-2006
2.00
Cut Holes for Trim Indicators, ELT and Ignition Sw
Details
       

 06-01-2006
2.00
Fabricate/Install SL40 Support Angles in Sub Panel
Details
       

 05-30-2006
0.50
Trim Air Gizmo Tray for Garmin 396 Handheld
Details
     

 05-30-2006
1.00
Fabricate/Install Support Strip for Trays
Details
       

 05-30-2006
1.00
Cut Slot in Sub-Panel for SL40 Comm Tray
Details
       

 05-30-2006
0.50
Acetone/Alodine Rails/Trays; Install Trays
Details
       

 05-28-2006
0.50
Mark Subpanel for SL40 Comm Cutout
Details
       

 05-28-2006
1.50
Drill Air Gizmo Tray to Rails for Garmin 396 GPS
Details
       

 05-27-2006
1.00
Drill SL40 Comm Tray to Rails
Details
       

 05-27-2006
1.00
Drill GTX327 Transponder Tray to Rails
Details
       

 05-27-2006
1.00
Drill GMA340 Audio Tray to Rails
Details
       

 05-26-2006
1.00
Rivet Support Angles for Radio Stack to Panel
Details
       

 05-26-2006
1.00
Fabricate / Drill Support Angles for Radio Stack
Details
       

 05-14-2006
2.00
Cut Panel for Radios and GPS
Details
     

 05-12-2006
0.50
Temporarily Install Dynon's, Panel; Sit Back and E
Details
       

 05-12-2006
0.50
Drill Remaining Instrument Attach Holes
Details
       

 05-11-2006
0.50
Use Jig to Drill Instrument Attach Holes
Details
       

 05-11-2006
0.50
Temporarily Install Dynon EMS in Panel
Details
       

 05-11-2006
1.50
Mark / Punch Eight 3-1/8" Instrument Panel Holes
Details
       










Copyright © 2001-2024 Matronics. All Rights Reserved.