Powered By Kitlog Pro v2.0
Steve's CH750 Cruzer (N750SB)
CH750 Cruzer
Engine
Work Logs Found:
66
Category Work Time:
225 Hours
Date
Hours
Work Log Summary
Details
02-23-2019
0.75
Replaced ECU
Details
02-21-2019
2.75
Compression Test
Details
02-19-2019
1.75
Test run before inspection
Details
01-08-2019
2.50
Cowling work
Details
12-27-2018
4.00
More sanding and smoothing of cowl halves
Details
11-24-2018
2.25
Final securement of lines and wires in engine area
Details
11-24-2018
2.25
Added fuel line brackets in cabin and connected fi
Details
11-23-2018
3.75
Viking Fuel Orifice
Details
11-02-2018
4.25
Fabricated and installed bottom channel cover
Details
10-15-2018
3.50
Install relay switch, reinstall ECU
Details
10-15-2018
1.75
Bolted and sealed firewall pass-thru
Details
10-13-2018
1.00
Finish coolant kit install
Details
10-08-2018
11.00
Fabricated new airbox
Details
10-08-2018
1.75
Coolant fill and Thermostat mods
Details
09-10-2018
5.00
Covering up cowl rivets
Details
09-08-2018
8.00
More cowling work
Details
09-07-2018
2.00
Throttle idle stop spacer
Details
08-14-2018
4.25
Additional cowling clean-up
Details
08-12-2018
4.25
Fiberglassing lower cowl profile
Details
08-11-2018
5.50
Bottom cowl foam and fiberglass
Details
08-10-2018
2.50
Prep work on bottom cowl
Details
08-05-2018
3.25
Cowling fiberglass work - Upper
Details
08-04-2018
3.25
Initial fiberglass work on nose profile
Details
08-03-2018
4.75
Upgraded gearbox vent system
Details
08-03-2018
2.50
Prepping cowling nose for fiberglass work
Details
06-23-2018
6.75
Top cowl work
Details
06-22-2018
2.75
Fitting upper cowling
Details
06-16-2018
2.75
Lower cowling exhaust/scoop
Details
05-28-2018
3.75
Attached lower cowling
Details
05-27-2018
3.00
Lower cowling work, lowered airbox opening
Details
05-26-2018
3.75
Initial work on bottom cowling
Details
03-15-2018
2.00
Relocated throttle
Details
11-11-2017
4.00
Fuel routing almost done
Details
11-05-2017
2.00
Fabricated platform for fuel components
Details
11-04-2017
6.00
Finalizing fuel route
Details
10-16-2017
1.00
Burping the cooling system
Details
10-14-2017
5.75
1st START!
Details
10-13-2017
7.50
Firming up some plumbing
Details
10-07-2017
2.00
Planning fuel routing
Details
10-06-2017
8.50
Avionics shelf fastening, Heater mounting
Details
10-01-2017
4.50
Hose and heater work
Details
09-30-2017
4.50
Plumbing the engine
Details
09-29-2017
1.50
Finished flywheel bracket update
Details
09-29-2017
5.50
Completed connections and tested engine wiring
Details
09-19-2017
0.75
Started install of new flywheel part
Details
09-16-2017
7.75
Wiring coming together
Details
09-12-2017
2.50
Continuing to wire
Details
09-04-2017
5.50
More wiring cables
Details
09-03-2017
2.50
Fuse area wiring
Details
08-25-2017
1.45
Temporarily mounted Viking View display
Details
08-19-2017
5.25
Continuing engine hookup
Details
08-18-2017
5.50
Engine Electrical and cable
Details
08-11-2017
3.00
Finish up airbox
Details
08-10-2017
6.50
Radiator Air Box
Details
08-08-2017
2.00
Firewall wiring passthrough
Details
08-08-2017
3.25
Cooling system/Radiator
Details
08-07-2017
4.50
Planning/Shelf
Details
08-01-2017
3.25
Mounted Engine to Airframe
Details
07-25-2017
1.25
Finished drilling for motor mount
Details
07-23-2017
2.50
Drilling firewall mount holes
Details
07-20-2017
2.00
Receiving Engine Part 4
Details
07-20-2017
0.00
Receiving Engine Part 3
Details
07-20-2017
0.00
Receiving Engine Part 2
Details
07-20-2017
0.00
Receiving Engine Part 1
Details
06-20-2017
0.00
Placed order for Viking 130
Details
03-25-2017
0.00
Road trip to see Viking install
Details
SITE NAVIGATION
Contact Builder
CH750 Cruzer Home
Category
# Logs
# Hours
All
580
2029
Avionics/Electrical
31
143
Cabin
74
220
Doors/Windows
24
96
Elevator
22
71
Engine
66
225
Firewall
11
28
Flaperons
13
56
Fuel System
9
30
Fuselage
35
136
Horizontal Stabilize
23
113
Landing Gear
31
78
Miscellaneous
21
41
Prop
2
4
Rudder
13
42
Shop Prep
7
22
Travel
1
15
Vertical Fin
13
45
Wing - Port
92
332
Wings
92
332
Copyright © 2001-2024 Matronics. All Rights Reserved.
