KitLog pro

Powered By Kitlog Pro v2.0

Steve & Nancy Riffe
Work Logs Found: 77
Category Work Time: 161 Hours
 Date
Hours
Work Log Summary

Details

 05-30-2017
0.00
Airworthiness Inspection
Details
     

 05-26-2017
0.50
New data plate, xponder check
Details
     

 05-10-2017
4.00

Details
       

 05-08-2017
1.00
Rub spot on upper cowl
Details
     

 05-06-2017
1.00
Resolve xponder, began dis-assembly
Details
       

 05-05-2017
0.10
Taxi test, brake check
Details
       

 05-04-2017
3.00
Wig-wag, trim, flap setup, brake line work
Details
       

 05-03-2017
3.00
Fuel tank calibration-2
Details
     

 05-02-2017
4.00
Fuel tank calibration-1
Details
       

 05-01-2017
3.00
Dynon calibrations-1
Details
       

 04-20-2017
4.00
Measurements for cg
Details
       

 04-19-2017
0.10
Weighing the plane-2
Details
       

 04-19-2017
4.00
Weighing the plane-1
Details
       

 04-18-2017
2.00
Install Transponder & b.u. battery
Details
       

 04-14-2017
1.00
Swapped clecos for screws
Details
     

 04-11-2017
2.00
Install engine cowl, drain r. fuel tank
Details
     

 04-10-2017
2.00
Engine run 3
Details
       

 04-08-2017
1.00
2nd Engine Run
Details

 04-06-2017
1.00
Intersection fairings-final
Details
     

 04-04-2017
2.00
Instersection fairings-11, clean canopy
Details
       

 04-03-2017
2.00
Intersection fairings-10, Crow belts-rear
Details
       

 03-31-2017
2.00
Intersection Fairings-9, Crow belts, fuel sender
Details
       

 03-27-2017
2.00
Intersection fairings-8
Details
       

 03-25-2017
1.00
Troubleshoot fuel pressure, test ELT
Details

 03-24-2017
1.00
Complete log books, ELT registration
Details

 03-23-2017
2.00
Intersection fairings-7, r. wing tip primer
Details
       

 03-22-2017
2.00
Intersection fairings-6, tail wheel springs
Details
       

 03-21-2017
2.00
Intersection fairings-5
Details
     

 03-20-2017
2.00
Intersection fairings-4
Details
       

 03-18-2017
3.00
First Engine Start!
Details
       

 03-17-2017
2.00
Intersection fairings-3
Details
       

 03-16-2017
2.00
Intersection fairings-3
Details
       

 03-15-2017
0.00
FAA registration complete
Details

 03-14-2017
3.00
Intersection fairings-2, red cube bracket
Details
       

 03-13-2017
2.00
Intersection fairings-1
Details
       

 03-11-2017
1.00
Remove canopy plastic sheeting
Details
     

 03-10-2017
3.00
Work on loose R. wing tip
Details
       

 03-10-2017
0.10
More pics of wing tip--see prev. post
Details
       

 03-09-2017
3.00
Adjust ailerons, install floors & seats
Details
       

 03-07-2017
4.00
Roll servo, snorkel, intersection fairings
Details
       

 03-06-2017
4.00
Registration forms, roll servo, L.. wing root gap
Details

 03-02-2017
4.00
A mostly unproductive day
Details
     

 02-28-2017
1.00
Empenage fairing, Dynon install, gas caps
Details
       

 02-27-2017
3.00
L. wing root gap seals, safety oil sender
Details
       

 02-25-2017
1.00
Adjust elevator trim
Details
       

 02-24-2017
4.00
Data plate, landing lights, gap seal
Details
       

 02-23-2017
2.00
Wing root fairing--rubber channel
Details
     

 02-22-2017
1.00
Apply N numbers, ground R. wing tip
Details
       

 02-21-2017
3.00
Wire left wing tip-nav/strobe & antenna
Details
       

 02-17-2017
3.00
Nav/strobe wiring at wing tips
Details
       

 02-14-2017
1.00
Install HID landing light bulbs
Details

 02-13-2017
3.00
Fuel sender wires, adjust flaps
Details
       

 02-11-2017
2.00
Installed com antennas, trim springs
Details
     

 02-10-2017
4.00
Rig ailerons, install mid cabin covers
Details
       

 02-09-2017
3.00
Trim wires, rudder install, avionics install
Details
       

 02-08-2017
2.00
Added engine oil, start wing tip wiring
Details
     

 02-07-2017
1.00
Install quick drain oil plug
Details
       

 02-06-2017
3.00
Misc items
Details
       

 02-03-2017
2.00
Landing lights, instruments, rudder horn
Details
       

 02-01-2017
1.00
Install quick drain oil plug
Details
       

 01-30-2017
2.00
Nav/strobe, roll servo wiring
Details
       

 01-27-2017
3.00
Pulled wires to wing tips
Details
       

 01-26-2017
4.00
Attach aileron controls, flap pushrods, pull wires
Details
       

 01-23-2017
2.00
Install flap hinge pins
Details
       

 01-21-2017
2.00
Finish Aileron, AOA/Pitot line,fuell vent install
Details
       

 01-20-2017
2.00
Safety wire tank brackets,AOA & Pitot lines
Details
       

 01-19-2017
2.00
Torque rear spar bolts, add screws to lower skin
Details
     

 01-18-2017
3.00
Torque wing bolts
Details
       

 01-17-2017
4.00
Final wing bolt install
Details
       

 01-16-2017
3.00
Fuel system check
Details
       

 01-10-2017
1.00
Finished VS install, prep for fuel flow
Details
       

 01-03-2017
1.00
Sloshed l. tank, install Andair fuel valve handle
Details
     

 01-02-2017
2.00
Checked R fuel tank for trash
Details
       

 01-01-2017
1.00
Install VS, torque fuel lines
Details
       

 12-31-2016
2.00
Elevator install, connect fuel lines
Details
       

 12-30-2016
1.00
Install wings with temp bolts
Details
       

 12-26-2016
0.50
Install HS
Details
       










Copyright © 2001-2024 Matronics. All Rights Reserved.