KitLog pro

Powered By Kitlog Pro v2.0

Davids Pipistrel Build Website
Work Logs Found: 41
Category Work Time: 92 Hours
 Date
Hours
Work Log Summary

Details

 10-02-2021
1.00
Performed Weight and Balance
Details

 09-26-2021
8.00
Trailered airplane and wings to airport hanger and
Details
       

 09-12-2021
4.00
Manufactured and install Experimental and N-number
Details

 09-05-2021
2.00
Installed all placards and information stickers
Details

 08-22-2021
1.00
Installed seat belts and seats

 09-08-2019
1.00
Added stickers to various controls and installed f
Details

 08-18-2019
2.00
Wired circuit board on Ray Allen control sticks
Details
     

 05-28-2019
1.00
Installed bagage compartment components for markng
Details

 05-27-2019
4.00
Installed velcro for seats and Dynon instruments
Details

 05-26-2019
1.00
Drilled holes for transponder antenna cable in rea
Details

 04-13-2019
2.00
Attached pedal adjustment springs to bottom of fus

 12-29-2018
2.00
Installed Cockpit light

 03-04-2018
1.00
Installed Cockpit light
Details
       

 04-15-2017
1.00
Installed landing light
Details

 03-17-2017
3.00
Swapped out incandescent landing light bulb
Details
       

 01-27-2016
1.00
Finished left airbrake
Details
       

 01-20-2016
1.50
Assembled airbrake and installed in wing.
Details

 01-15-2016
1.50
fitted left airbrake
Details

 01-14-2016
1.50
Trial assembled left airbrake
Details

 01-13-2016
1.50
Prepared and test assembled left airbrake
Details

 01-12-2016
1.50
Ground top side base of left wing
Details
       

 01-04-2016
1.50
Fitted wing tip light lens to wingtip
     

 01-02-2016
2.50
pulled wires for stobe lights
Details
       

 01-02-2016
2.00
Fitting strobe lights into wing

 11-22-2015
3.00
Repaired holes in fuselage
Details

 11-22-2015
2.00
Drilled holes for static air
Details

 09-12-2015
4.00
Installed Tanis engine heater to my Rotax 912 is S
Details

 09-07-2015
2.00
Wired the trim controller and trim motor
Details
       

 09-05-2015
1.00
Attempted to install Static Air Vents
Details
       

 09-04-2015
2.00
Installed OAT Probe
       

 09-04-2015
3.00
Installed Dynon ADAHRS unit
       

 08-30-2015
2.00
Cut holes in firewall upholstery and firewall heat
Details
     

 08-29-2015
2.00
Installed the forward side upholstery
Details
       

 08-29-2015
2.00
Applied the insulated firewall upholstery to the c
Details
     

 08-23-2015
1.00
Mounted Oil reservoir bracket
Details
     

 08-22-2015
4.00
Studied Pipistrel Schematics
Details

 08-08-2015
3.00
Assembled Instrument panel
Details
     

 06-28-2015
8.00
Installed interior upholstery
Details
       

 06-14-2015
2.00
Glued Firewall heat shield in place
Details

 06-07-2015
1.50
Fit the firewall heat shield
Details

 05-29-2015
0.50
Fixed throttle quadrant
Details










Copyright © 2001-2024 Matronics. All Rights Reserved.