Powered By Kitlog Pro v2.0
Steves Web Site
Velocity SE
All
Work Logs Found:
66
Category Work Time:
128 Hours
Date
Hours
Work Log Summary
Details
03-19-2017
4.00
Dog House - Hidden Hinge
Details
03-18-2017
2.00
Rework the canard saddle
Details
03-08-2017
3.00
Glassed (fabricated) the canard torsion tabs.
Details
02-28-2017
2.00
Canard attachment lay-up prep
Details
02-26-2017
1.00
Popped off Dog-House
Details
02-25-2017
2.00
Hatch Hinge
Details
02-25-2017
2.00
Hatch Hinge
Details
02-25-2017
5.00
Doghouse layups
Details
02-22-2017
1.50
Canard "left off"
Details
02-20-2017
3.50
Canard alignment and drilling
02-19-2017
4.00
Layup reinforcements for canard
Details
02-18-2017
3.00
Elevator repair - Part 1
Details
02-12-2017
2.00
Trim Hatch
Details
02-12-2017
2.00
Lay-up cover for front of keel
Details
02-08-2017
2.00
Hatch hinge layout
Details
02-04-2017
3.00
Preliminary fit to fuse
Details
02-02-2017
1.00
Elevator hinge screws
Details
01-29-2017
2.00
Elevator counter weights
Details
01-28-2017
4.00
Drill bushings and countersink
Details
01-24-2017
1.00
Trim right elevator to correct length
Details
01-23-2017
1.50
Canard
Details
01-22-2017
3.00
Move engine to storage unit
Details
01-22-2017
2.00
Elevator Hinges and Initial Rigging
Details
01-19-2017
2.00
Bore Scope
Details
01-02-2017
2.00
Canard Center Hinge
Details
01-01-2017
3.00
Bond Hinges to Canard
Details
12-31-2016
3.50
Bond elevator hinges
Details
12-30-2016
0.00
New to me Engine...!
Details
12-30-2016
3.50
Begin install elevator hinges
Details
12-29-2016
2.50
Trim trailing edge of canard
Details
12-28-2016
2.50
Machined canard hinges
Details
12-23-2016
4.00
Attach hinges to 2x seats
Details
12-22-2016
2.50
Aileron torque tube attachment
Details
12-21-2016
3.00
Rework of seat hardpoints / Keel airleron bearing
Details
12-18-2016
2.50
Glass LHS gear bushings
Details
12-17-2016
2.00
Glass-in RHS gear bushings
Details
12-11-2016
3.00
Glue in main gear bushings
Details
12-10-2016
2.00
Final prep for gluing-in landing gear bushings
Details
12-07-2016
1.50
Finish drill LHS gear mount
Details
12-04-2016
1.00
LHS mian gear attachment
Details
12-03-2016
1.50
Locate and drill pilot holes for LH side gear bolt
Details
10-30-2016
2.50
Install 2" flange to warm-air duct
Details
10-29-2016
2.00
Lay-up patch to cover 1.75" warm-air vent hole
Details
10-23-2016
0.50
Lay-up patch to cover 2x 1.5" holes in oil-cooler
Details
10-22-2016
3.00
Warm-air ducting
Details
10-18-2016
2.00
Prime small aluminum parts.
Details
10-16-2016
1.50
Prep various aluminum parts for primer. Treat with
Details
10-15-2016
1.50
Locate and drill rudder pedal bellcrank support br
Details
10-12-2016
2.00
Second layer glass on oil cooler flange. Locate an
Details
10-10-2016
1.00
Sand interior of nose section and oil cooler bypas
Details
10-09-2016
1.00
Glass (fabricate) oil cooler attachment flange
Details
10-08-2016
2.50
Remove masking tape from windows
Details
10-06-2016
0.50
Remove masking tape from windows
Details
10-02-2016
3.00
Remove masking tape from windows
Details
09-10-2016
4.00
Inventory small parts, begin clean tape residue fr
Details
09-09-2016
0.00
Truck wings to Piqua
Details
09-05-2016
3.00
Inventory a photograph parts
Details
09-04-2016
0.00
Details
09-04-2016
0.00
Details
09-04-2016
0.00
Details
08-07-2016
0.00
Details
08-07-2016
0.00
08-07-2016
0.00
08-07-2016
0.00
08-07-2016
0.00
Details
08-07-2016
0.00
Details
SITE NAVIGATION
Velocity SE Home
Category
# Logs
# Hours
All
66
128
Bringing it Home - I
6
7
Canard
25
64
Engine
3
5
Fuselage
12
22
Hatch (nose)
2
4
Keel / Control Linka
1
2
Landing Gear
7
14
Pre-Buy Photos
6
Seats
1
4
Windows and Interior
3
6
Copyright © 2001-2025 Matronics. All Rights Reserved.
