Date
|
Hours
|
Work Log Summary
|
Details
|
06-17-2011
|
1.00
|
Airworthiness Certificate!
|
Details
|
|
|
06-16-2011
|
5.00
|
Airworthiness Inspection Preparation
|
Details
|
|
|
06-15-2011
|
8.50
|
Placards, glove box, etc
|
Details
|
|
|
06-14-2011
|
9.00
|
Weigh airplane, calibrate fuel
|
Details
|
|
|
06-13-2011
|
9.00
|
Canard, Elevator push tube, prepare for weight
|
Details
|
|
|
06-12-2011
|
5.00
|
Nose gear washers, Cowl nut plates
|
Details
|
|
|
06-11-2011
|
8.50
|
Seat belts, roll servo, gear swing
|
Details
|
|
|
06-10-2011
|
8.00
|
Roll servo hardpoints, seatbelts
|
Details
|
|
|
06-09-2011
|
8.00
|
Gear swinging, inspections
|
Details
|
|
|
|
06-08-2011
|
7.00
|
Heater ducting, gear doors, gear cables, etec
|
Details
|
|
|
06-02-2011
|
7.00
|
Heater controls, doors, heater tubing
|
Details
|
|
|
06-01-2011
|
3.50
|
Reattach under cowling flight controls
|
Details
|
|
|
|
06-01-2011
|
4.00
|
Cooling plenum
|
Details
|
|
|
05-31-2011
|
7.50
|
Cowling, plenum,
|
Details
|
|
|
05-30-2011
|
5.00
|
Heater controls
|
Details
|
|
|
05-30-2011
|
4.50
|
Cowling, Pitch trim, elevator
|
Details
|
|
|
05-29-2011
|
4.00
|
Secure wireing
|
Details
|
|
|
|
05-29-2011
|
4.00
|
Cowling
|
Details
|
|
|
|
05-28-2011
|
4.50
|
Secure electrical wireing
|
Details
|
|
|
05-28-2011
|
4.00
|
Cowling
|
Details
|
|
|
05-27-2011
|
4.25
|
Trim interior pieces
|
Details
|
|
|
05-27-2011
|
4.25
|
Cowling
|
Details
|
|
|
05-26-2011
|
4.00
|
Trim interior parts for upholstery
|
Details
|
|
|
05-26-2011
|
4.00
|
Cowling
|
Details
|
|
|
05-25-2011
|
8.00
|
Cowling
|
Details
|
|
|
|
05-01-2011
|
0.00
|
Upholstery
|
Details
|
|
|
05-01-2011
|
8.00
|
Cowling, Nose cover
|
Details
|
|
|
04-30-2011
|
8.00
|
Cowling
|
Details
|
|
|
04-29-2011
|
10.50
|
Cowling
|
Details
|
|
|
04-28-2011
|
10.50
|
Cowling
|
Details
|
|
|
04-27-2011
|
8.00
|
Cowling
|
Details
|
|
|
04-26-2011
|
3.50
|
Redo Center Seat Support
|
Details
|
|
|
04-26-2011
|
4.50
|
Cowling
|
Details
|
|
|
04-08-2011
|
6.00
|
Interior ready for upholstery
|
Details
|
|
|
04-07-2011
|
12.00
|
Vanity/Baggage panel, cargo tiedown rings
|
Details
|
|
|
04-06-2011
|
7.50
|
Vanity/Baggage panels
|
Details
|
|
|
04-05-2011
|
7.50
|
Cargo tie downs, door posts
|
Details
|
|
|
04-03-2011
|
11.25
|
Rear Seat, Overhead plenum
|
Details
|
|
|
04-02-2011
|
9.00
|
Vanity/Baggage panel, door sils, overhead
|
Details
|
|
|
04-01-2011
|
9.50
|
Door sils, Vanity/Baggage panel
|
Details
|
|
|
03-31-2011
|
8.00
|
Vanity/Baggage panels, door sils
|
Details
|
|
|
03-29-2011
|
9.00
|
Overhead plenum, Vanity panels
|
Details
|
|
|
03-28-2011
|
7.00
|
Seat belt hardpoints, misc
|
Details
|
|
|
03-26-2011
|
4.00
|
Miscellaneous
|
Details
|
|
|
|
03-25-2011
|
6.00
|
Overhead lights, vents, and vanity panel
|
Details
|
|
|
03-24-2011
|
6.00
|
Set up engine fuel pressures
|
Details
|
|
|
|
03-23-2011
|
7.00
|
More Miscelaneous work
|
Details
|
|
|
|
03-22-2011
|
6.00
|
Miscellaneous work
|
|
|
|
|
03-21-2011
|
6.00
|
Preoiler CB, sump drain, etc
|
Details
|
|
|
03-19-2011
|
4.00
|
Setup EFIS and EIS
|
Details
|
|
|
|
03-19-2011
|
2.00
|
Reinstall Aileron
|
Details
|
|
|
|
03-18-2011
|
6.00
|
Start engine
|
Details
|
|
|
03-17-2011
|
4.00
|
Setup EIS
|
Details
|
|
|
|
03-17-2011
|
3.50
|
Balance ailerons
|
Details
|
|
|
03-17-2011
|
1.50
|
Add Fuel
|
Details
|
|
|
|
03-14-2011
|
5.00
|
Wireing and "power up"
|
Details
|
|
|
03-14-2011
|
4.00
|
Balance elevators
|
Details
|
|
|
|
03-13-2011
|
8.50
|
Control balance, fuel s/o valves, etc
|
Details
|
|
|
03-12-2011
|
7.50
|
Wireing, etc
|
Details
|
|
|
|
03-11-2011
|
8.00
|
Install Pitot/static system
|
Details
|
|
|
03-10-2011
|
3.00
|
Miscellaneous wireing
|
Details
|
|
|
|
03-10-2011
|
3.00
|
Install pitot tube and static port
|
Details
|
|
|
|
03-09-2011
|
7.50
|
More Wireing
|
Details
|
|
|
03-08-2011
|
6.50
|
ELT, Stick, Wireing
|
Details
|
|
|
03-07-2011
|
2.50
|
Oil-Air separator
|
Details
|
|
|
03-07-2011
|
5.00
|
ELT install
|
Details
|
|
|
03-04-2011
|
8.00
|
Cut exhaust pipes and cowling hole
|
Details
|
|
|
03-03-2011
|
2.50
|
Install com panel
|
Details
|
|
|
03-03-2011
|
5.00
|
Engine exhaust, elevator ends
|
Details
|
|
|
03-02-2011
|
6.50
|
Stby alternator, route coax, treat elevator ends
|
Details
|
|
|
03-01-2011
|
4.00
|
Miscellaneous Electrical
|
Details
|
|
|
03-01-2011
|
2.50
|
Air/Oil seperator
|
Details
|
|
|
02-28-2011
|
3.00
|
Tighten up connections
|
Details
|
|
|
|
02-28-2011
|
4.00
|
Starter replacement, wireing connectors
|
Details
|
|
|
02-25-2011
|
4.00
|
Install pilot seat
|
Details
|
|
|
02-25-2011
|
2.00
|
Install GS Shelf
|
Details
|
|
|
02-24-2011
|
6.00
|
Wireing and Pilot seat mount
|
Details
|
|
|
02-23-2011
|
4.00
|
Wireing
|
Details
|
|
|
02-23-2011
|
4.00
|
Move Pilot seat forward
|
Details
|
|
|
02-22-2011
|
7.50
|
Wireing
|
Details
|
|
|
02-21-2011
|
6.50
|
Wireing and magnetometer install
|
Details
|
|
|
02-19-2011
|
8.00
|
Magnetometer installation
|
Details
|
|
|
02-18-2011
|
6.00
|
Magnetometer installation
|
Details
|
|
|
02-17-2011
|
3.00
|
Secure starter cables
|
Details
|
|
|
02-17-2011
|
4.00
|
Fuel SO Valve
|
Details
|
|
|
02-16-2011
|
7.00
|
Fuel Shutoff Valve
|
Details
|
|
|
02-15-2011
|
7.00
|
Door warning switches, secure wireing
|
Details
|
|
|
02-14-2011
|
6.50
|
CHT/EGT, secure wires,
|
Details
|
|
|
02-11-2011
|
7.00
|
Trim and secure wireing
|
Details
|
|
|
02-10-2011
|
3.50
|
Roll trim, secure wireing
|
Details
|
|
|
02-07-2011
|
0.00
|
New Digs
|
Details
|
|
|
02-05-2011
|
8.00
|
Install roll servo, AHRS
|
Details
|
|
|
02-03-2011
|
7.50
|
Engine drain lines, control cables, pitot tube
|
Details
|
|
|
|
02-02-2011
|
7.50
|
Engine mounts, Prop mounted
|
Details
|
|
|
02-01-2011
|
7.50
|
Enging mounts, Landing light, Pitch servo
|
Details
|
|
|
01-31-2011
|
5.50
|
Fuel pump, Landing light, Engine drain lines
|
Details
|
|
|
|
01-30-2011
|
4.50
|
Landing light, Prop backplate
|
Details
|
|
|
01-29-2011
|
7.50
|
Prop backplate, Landing light
|
Details
|
|
|
01-28-2011
|
4.50
|
Prepare spinner, Electrical
|
Details
|
|
|
01-27-2011
|
7.50
|
Wireing, Accessory shelf, Pitch trim
|
Details
|
|
|
01-26-2011
|
6.50
|
Wireing
|
Details
|
|
|
01-25-2011
|
5.50
|
Wireing
|
Details
|
|
|
01-24-2011
|
6.00
|
Ran Electrical wires
|
Details
|
|
|
01-19-2011
|
5.50
|
Install trim servo
|
Details
|
|
|
01-18-2011
|
7.00
|
Placement of peripheral electrical components
|
Details
|
|
|
|
01-17-2011
|
7.00
|
Install Electrical platform for peripheries
|
Details
|
|
|
01-14-2011
|
6.00
|
Secure Engine control cables
|
Details
|
|
|
|
01-13-2011
|
5.50
|
Fit Seats, Plan upholstery
|
Details
|
|
|
01-12-2011
|
7.00
|
Engine control cables
|
Details
|
|
|
01-11-2011
|
6.00
|
Install engine control cables
|
Details
|
|
|
01-10-2011
|
6.00
|
Install Panel
|
Details
|
|
|
01-07-2011
|
6.50
|
Seats, Keel cover, comm panel
|
Details
|
|
|
01-06-2011
|
5.00
|
Install fuel pump, clean windshield, etc
|
Details
|
|
|
01-05-2011
|
7.00
|
|
Details
|
|
|
01-04-2011
|
6.00
|
Com Panel Install
|
Details
|
|
|
|
12-30-2010
|
5.00
|
Install Fuel pump and filter plus other
|
Details
|
|
|
|
12-29-2010
|
7.00
|
Com Panel, Overhead plenum
|
Details
|
|
|
12-28-2010
|
6.00
|
Door micro switches, etc
|
Details
|
|
|
12-27-2010
|
6.50
|
Install Firewall Electrical components
|
Details
|
|
|
12-23-2010
|
7.00
|
Install Cht and egt sensors
|
Details
|
|
|
12-22-2010
|
6.00
|
Install Prop Governor
|
Details
|
|
|
12-21-2010
|
6.50
|
Tac pickup on Mag
|
Details
|
|
|
12-20-2010
|
7.50
|
Seat Intallation
|
Details
|
|
|
12-17-2010
|
7.50
|
Install rear seats
|
Details
|
|
|
12-16-2010
|
7.00
|
Install rear seats
|
Details
|
|
|
12-15-2010
|
6.00
|
Install rear seats
|
Details
|
|
|
12-14-2010
|
2.00
|
Rear seat install
|
Details
|
|
|
|
12-14-2010
|
5.00
|
Elevator push tube
|
Details
|
|
|
12-13-2010
|
5.00
|
Concentric torque tube and counter weights
|
Details
|
|
|
|
12-10-2010
|
6.50
|
Secure hoses and wireing on engine
|
Details
|
|
|
12-09-2010
|
7.00
|
Started wireing
|
Details
|
|
|
12-08-2010
|
7.50
|
Run EI leads, Place lights in overhead
|
Details
|
|
|
12-07-2010
|
5.00
|
Install more plumbing, plugs, and Mag leads
|
Details
|
|
|
12-07-2010
|
3.00
|
Adjust copilot seat
|
Details
|
|
|
12-06-2010
|
7.00
|
Engine Fuel/Pressure lines
|
Details
|
|
|
12-03-2010
|
6.50
|
Fuel and oil lines
|
Details
|
|
|
12-02-2010
|
6.50
|
Fuel and oil lines
|
Details
|
|
|
12-01-2010
|
7.50
|
Throttle bracket and drain lines
|
Details
|
|
|
11-30-2010
|
7.50
|
Fabricate throttle cable bracket
|
Details
|
|
|
11-29-2010
|
7.50
|
Mixture and Throttle Bracket
|
Details
|
|
|
11-24-2010
|
7.50
|
Fuel lines
|
Details
|
|
|
11-23-2010
|
7.50
|
Install fuel lines
|
Details
|
|
|
11-22-2010
|
7.00
|
Install Electroair CSTW
|
Details
|
|
|
11-20-2010
|
3.50
|
Intercylinder baffles
|
Details
|
|
|
11-19-2010
|
7.50
|
Intercylinder baffles
|
Details
|
|
|
|
11-18-2010
|
4.00
|
Pre-oiler and firewall components
|
Details
|
|
|
11-09-2010
|
6.50
|
Intercylinder Baffles
|
Details
|
|
|
11-08-2010
|
2.00
|
Engine Baffling
|
Details
|
|
|
|
11-07-2010
|
1.00
|
test
|
Details
|
|
|
|
11-06-2010
|
8.50
|
Rudder and Ailerons
|
Details
|
|
|
11-05-2010
|
8.00
|
Rigging ailerons
|
Details
|
|
|
|
11-04-2010
|
8.00
|
Rudders and Ailerons
|
Details
|
|
|
11-02-2010
|
8.00
|
Pilot side rudder cable
|
Details
|
|
|
11-01-2010
|
6.00
|
Rig pilot side aileron
|
Details
|
|
|
10-30-2010
|
4.50
|
Aileron bellcrank bracketw
|
Details
|
|
|
10-29-2010
|
4.00
|
Rudder installation
|
Details
|
|
|
10-29-2010
|
3.50
|
Install aileron bell crank assemply
|
Details
|
|
|
10-28-2010
|
7.50
|
Install rudder and hinges
|
Details
|
|
|
10-27-2010
|
7.00
|
Install torque tubes on ailerons
|
Details
|
|
|
|
10-26-2010
|
8.00
|
Install aileron hinges
|
Details
|
|
|
10-25-2010
|
8.15
|
Rudder hinges and wells
|
Details
|
|
|
10-25-2010
|
4.00
|
glass in Glide Slope antenna
|
Details
|
|
|
10-23-2010
|
6.00
|
Mount aileron
|
Details
|
|
|
10-22-2010
|
8.00
|
Install piano hinge on airlerons
|
Details
|
|
|
10-21-2010
|
4.00
|
Install firewall material on wing
|
Details
|
|
|
10-19-2010
|
7.00
|
Cooling Plenum
|
Details
|
|
|
10-14-2010
|
6.50
|
12.3.4
|
Details
|
|
|
10-13-2010
|
7.50
|
Cooling plenum
|
Details
|
|
|
10-12-2010
|
7.00
|
Cooling Plenum
|
Details
|
|
|
10-11-2010
|
8.00
|
Brake bleeding
|
Details
|
|
|
|
10-09-2010
|
8.00
|
Cooling plenum and doors
|
Details
|
|
|
10-08-2010
|
11.00
|
Plenum and doors
|
Details
|
|
|
10-07-2010
|
9.00
|
5.3.3
|
Details
|
|
|
10-06-2010
|
8.00
|
Engine cooling plenum
|
Details
|
|
|
|
10-05-2010
|
8.00
|
Wheels and brakes installed
|
Details
|
|
|
|
10-04-2010
|
8.50
|
Install gear micro switches
|
Details
|
|
|
|
10-02-2010
|
7.00
|
Reinstall fuel lines
|
Details
|
|
|
10-01-2010
|
5.00
|
Nose gear doors, hydraulic lines
|
Details
|
|
|
09-30-2010
|
8.75
|
Repair hydraulic pump
|
Details
|
|
|
09-29-2010
|
9.00
|
Fuel and vent lines
|
Details
|
|
|
09-28-2010
|
8.00
|
Fuel lines in cabin
|
Details
|
|
|
|
09-24-2010
|
9.00
|
Install brake lines, sockets
|
Details
|
|
|
09-23-2010
|
9.00
|
Permanent hardware in gear retraction system
|
Details
|
|
|
09-22-2010
|
8.00
|
More gear tweaking
|
Details
|
|
|
|
09-21-2010
|
9.00
|
Tweaking Gear retraction system
|
Details
|
|
|
09-20-2010
|
8.50
|
Main gear cable installation
|
Details
|
|
|
09-18-2010
|
8.50
|
Install nose gear closer
|
Details
|
|
|
09-17-2010
|
10.00
|
Secure Hydraulic lines
|
Details
|
|
|
09-16-2010
|
9.25
|
Hydraulic plumbinmg
|
Details
|
|
|
09-15-2010
|
8.25
|
Hydraulic line fabrication
|
Details
|
|
|
09-14-2010
|
8.25
|
Fitting Mishler's nose gear closer
|
Details
|
|
|
09-13-2010
|
9.50
|
Gear socket install, relief forms for fuel dump an
|
Details
|
|
|
09-12-2010
|
4.00
|
Prime nose gear leg. Install doors
|
Details
|
|
|
09-12-2010
|
2.50
|
Mold for fuel shutoff valve control
|
Details
|
|
|
09-10-2010
|
5.50
|
Remove nose gear leg and prepare for priming
|
Details
|
|
|
09-10-2010
|
3.50
|
Outboard end strake reinforcement
|
Details
|
|
|
09-09-2010
|
8.00
|
Primed wings and fuselage.
|
Details
|
|
|
09-08-2010
|
9.25
|
Prepare fuselage and wings for final prime
|
Details
|
|
|
09-07-2010
|
8.00
|
Fill with bondo and sand
|
Details
|
|
|
09-06-2010
|
7.50
|
Sand and fill wings and fuselage
|
Details
|
|
|
|
09-03-2010
|
8.50
|
Primed, guide coated, sanded
|
Details
|
|
|
09-02-2010
|
8.25
|
More finishing
|
Details
|
|
|
09-01-2010
|
9.00
|
Sanding and prep for prime
|
Details
|
|
|
|
08-31-2010
|
9.00
|
Sanding and filling
|
Details
|
|
|
08-30-2010
|
11.00
|
Wings on finish work
|
Details
|
|
|
08-28-2010
|
5.00
|
Sanded top of strake and fuselage
|
Details
|
|
|
08-28-2010
|
5.00
|
Install sump tank, glass bulkheads
|
Details
|
|
|
08-27-2010
|
9.00
|
Strake cutouts
|
Details
|
|
|
08-26-2010
|
3.50
|
Treat strake cutouts
|
Details
|
|
|
08-26-2010
|
3.00
|
Sump tank capacity and mounting tabs
|
Details
|
|
|
|
08-26-2010
|
2.00
|
Sanding Wings
|
Details
|
|
|
08-25-2010
|
8.00
|
Sanding and filling wings
|
Details
|
|
|
|
08-24-2010
|
3.00
|
Glass sump tank
|
Details
|
|
|
08-24-2010
|
6.50
|
Finishing wings
|
Details
|
|
|
08-23-2010
|
4.00
|
Hard coat wings
|
Details
|
|
|
08-23-2010
|
3.00
|
Cut corners off sump tank
|
Details
|
|
|
08-21-2010
|
3.50
|
Sump tank
|
Details
|
|
|
08-21-2010
|
5.00
|
Sanding and filling upper wings
|
Details
|
|
|
08-20-2010
|
8.00
|
Sanding and filling upper wings
|
Details
|
|
|
08-20-2010
|
5.00
|
Leak check CP fuel tanks
|
Details
|
|
|
08-20-2010
|
1.50
|
Instrument panel
|
Details
|
|
|
|
08-19-2010
|
8.50
|
Fitting panel
|
Details
|
|
|
08-19-2010
|
5.00
|
Finishing
|
Details
|
|
|
08-18-2010
|
3.25
|
Panel
|
Details
|
|
|
08-18-2010
|
5.25
|
Determine Hub lenght for Aero Composite prop
|
Details
|
|
|
08-17-2010
|
2.50
|
Modify Panel
|
Details
|
|
|
|
08-17-2010
|
6.00
|
Hang engine
|
Details
|
|
|
08-16-2010
|
8.50
|
Enging Mount and Cowling
|
Details
|
|
|
08-14-2010
|
12.00
|
Install Firewall
|
Details
|
|
|
08-13-2010
|
8.00
|
wetsand, install gear legs, check for leaks
|
Details
|
|
|
08-12-2010
|
9.00
|
wet sand and fuel tank leaks
|
Details
|
|
|
08-11-2010
|
8.00
|
Filling, last prime, fuel tank leak checks
|
Details
|
|
|
08-10-2010
|
11.50
|
More sanding
|
Details
|
|
|
08-09-2010
|
10.00
|
More sanding
|
Details
|
|
|
08-07-2010
|
10.75
|
CP wing/strake finishing
|
Details
|
|
|
08-06-2010
|
9.00
|
Sanded CP lowerwing/strake
|
Details
|
|
|
08-05-2010
|
11.00
|
CP wing and strake bottom
|
Details
|
|
|
08-04-2010
|
6.50
|
Finishing CP lower wing and strake
|
Details
|
|
|
07-29-2010
|
8.25
|
Sanding
|
Details
|
|
|
07-28-2010
|
8.25
|
Sanding
|
Details
|
|
|
07-27-2010
|
9.75
|
Sanding
|
Details
|
|
|
07-26-2010
|
8.50
|
Sanding
|
Details
|
|
|
07-24-2010
|
9.50
|
Sanding wings
|
Details
|
|
|
07-23-2010
|
8.25
|
Sand wing bottom and gear legs
|
Details
|
|
|
07-22-2010
|
8.00
|
Sanding
|
Details
|
|
|
07-21-2010
|
5.50
|
Micro pilot wing bottom
|
Details
|
|
|
07-21-2010
|
3.50
|
Install brake lines down gear leg
|
Details
|
|
|
07-20-2010
|
8.00
|
More sanding
|
Details
|
|
|
07-19-2010
|
8.00
|
Remove Bad Micro
|
Details
|
|
|
07-17-2010
|
8.00
|
Micro wing bottom
|
Details
|
|
|
07-16-2010
|
6.00
|
Prepping bottom of pilot wing/strake
|
Details
|
|
|
07-16-2010
|
2.50
|
Install landing light lense
|
Details
|
|
|
07-15-2010
|
2.00
|
Install plastic instrument panel
|
Details
|
|
|
07-15-2010
|
6.00
|
Install overhead fresh air duct
|
Details
|
|
|
07-14-2010
|
4.00
|
Modify overhead fresh air duct
|
Details
|
|
|
07-14-2010
|
5.50
|
Finish gear doors
|
Details
|
|
|
07-13-2010
|
7.00
|
Fuel vent system
|
Details
|
|
|
07-13-2010
|
2.50
|
CP gear door
|
Details
|
|
|
07-08-2010
|
4.00
|
Overhead "instrument" panel
|
Details
|
|
|
07-08-2010
|
4.75
|
Gear door fitting
|
Details
|
|
|
07-06-2010
|
3.00
|
overhead "instrument" panel
|
Details
|
|
|
07-06-2010
|
3.50
|
Gear doors
|
Details
|
|
|
07-05-2010
|
3.50
|
Glassed in Eng cooling NACA vents
|
Details
|
|
|
07-05-2010
|
6.50
|
Fitting gear doors
|
Details
|
|
|
07-03-2010
|
7.75
|
Gear doors
|
Details
|
|
|
07-02-2010
|
9.00
|
Gear doors
|
Details
|
|
|
07-01-2010
|
8.00
|
Prepare main gear doors
|
Details
|
|
|
06-30-2010
|
8.00
|
Glass inside wheel wells/cut gear leg
|
Details
|
|
|
06-29-2010
|
7.50
|
Preparing wheel well
|
Details
|
|
|
06-28-2010
|
6.00
|
Strake glassing
|
Details
|
|
|
06-26-2010
|
8.25
|
Glass in Slant fuel bulkheads
|
Details
|
|
|
06-25-2010
|
8.00
|
Jeffco slant baggage bulkheads
|
Details
|
|
|
06-24-2010
|
6.50
|
More fuel system glassing
|
Details
|
|
|
06-23-2010
|
2.00
|
Windscreen protection
|
Details
|
|
|
06-23-2010
|
1.50
|
Sanded wheel well area
|
Details
|
|
|
06-23-2010
|
5.00
|
Glass Main spar to strake and bulkhead
|
Details
|
|
|
06-22-2010
|
0.50
|
The Big Flip
|
Details
|
|
|
06-22-2010
|
4.00
|
Prepare sump tank
|
Details
|
|
|
06-22-2010
|
3.00
|
Door/strake
|
Details
|
|
|
|
06-21-2010
|
8.00
|
Install Leading edge strake tips
|
Details
|
|
|
06-18-2010
|
5.00
|
Seats, Strake
|
Details
|
|
|
06-09-2010
|
4.00
|
Install seats
|
Details
|
|
|
06-09-2010
|
4.00
|
Glass top strake to fuselage
|
Details
|
|
|
06-09-2010
|
2.00
|
Glass in pilot wheel/gear well
|
Details
|
|
|
06-09-2010
|
2.00
|
Glass in CP seat hardpoints
|
Details
|
|
|
06-09-2010
|
2.00
|
Glass in CP fuel sight guage
|
Details
|
|
|
06-07-2010
|
7.50
|
Seat Installation
|
Details
|
|
|
06-04-2010
|
6.50
|
Seat construction and hard points
|
Details
|
|
|
06-03-2010
|
2.00
|
Reshaping Glare shield attaching flanges
|
Details
|
|
|
06-03-2010
|
7.00
|
Pilot seat rail hard points
|
Details
|
|
|
06-02-2010
|
1.00
|
Reattach stiffening bar to panel
|
Details
|
|
|
06-02-2010
|
6.00
|
Pilot seat construction
|
Details
|
|
|
06-01-2010
|
3.00
|
Slot on Glareshield for panel
|
Details
|
|
|
06-01-2010
|
5.00
|
Assemble pilot seat
|
Details
|
|
|
05-31-2010
|
4.50
|
Glass underside of wheel well
|
Details
|
|
|
05-31-2010
|
4.00
|
Build upper flange onto panel
|
Details
|
|
|
05-29-2010
|
6.75
|
Glare shield fitting
|
Details
|
|
|
05-28-2010
|
3.00
|
Wing Strake cutout
|
Details
|
|
|
|
05-28-2010
|
5.00
|
Panel flange treatment
|
Details
|
|
|
05-22-2010
|
4.00
|
Panel
|
Details
|
|
|
05-21-2010
|
7.00
|
Panel
|
Details
|
|
|
05-20-2010
|
8.00
|
Panel fitting
|
Details
|
|
|
05-13-2010
|
6.00
|
Fixing copilot strake cover
|
Details
|
|
|
05-12-2010
|
8.00
|
Pilot Strake Covered!
|
Details
|
|
|
05-11-2010
|
6.00
|
Copilot Stake Covered!
|
Details
|
|
|
05-10-2010
|
7.50
|
Strake Prep
|
Details
|
|
|
05-01-2010
|
9.50
|
Jeffco and glassing strakes
|
Details
|
|
|
04-30-2010
|
7.00
|
Jeffco CP Strakes
|
Details
|
|
|
04-29-2010
|
8.00
|
Glassing Bulkheads and Baffles
|
Details
|
|
|
04-27-2010
|
10.50
|
Sight guage and bulkheads
|
Details
|
|
|
04-26-2010
|
8.00
|
Sight guage and bulkheads
|
Details
|
|
|
04-14-2010
|
7.00
|
Bulkheads and Jeffco
|
Details
|
|
|
04-13-2010
|
11.00
|
Bulkheads
|
Details
|
|
|
04-12-2010
|
6.50
|
Bulkheads and hardpoints
|
Details
|
|
|
04-09-2010
|
7.00
|
Bulkheads and Baffles
|
Details
|
|
|
04-08-2010
|
9.00
|
Hard points and bulkheads
|
Details
|
|
|
04-07-2010
|
4.00
|
Fuel system hardpoints
|
Details
|
|
|
04-07-2010
|
2.00
|
Copilot strake window
|
Details
|
|
|
03-16-2010
|
7.00
|
Copilot strake window, baffles
|
Details
|
|
|
03-15-2010
|
7.50
|
Install fuel caps, more bulkheads
|
Details
|
|
|
03-12-2010
|
8.00
|
Jeffco, fuel sender, copilot baffles
|
Details
|
|
|
03-11-2010
|
8.00
|
Glass in Baffles, Sight guages
|
Details
|
|
|
03-10-2010
|
3.00
|
Fuel strake bulkheads
|
Details
|
|
|
03-10-2010
|
4.00
|
Fuel Sight Guages
|
Details
|
|
|
03-05-2010
|
7.00
|
Install strake window, fuel sender bracket
|
Details
|
|
|
03-04-2010
|
6.00
|
Cut rabbit in plexiglass, Mounted fuel sender brac
|
Details
|
|
|
03-03-2010
|
8.00
|
Install baggage area windows
|
Details
|
|
|
03-02-2010
|
9.00
|
Epoxy fuel system hardpoints, glass bulkheads
|
Details
|
|
|
02-26-2010
|
8.00
|
More bulkhead work
|
Details
|
|
|
02-25-2010
|
9.50
|
Copilot wheel well
|
Details
|
|
|
02-24-2010
|
8.00
|
Fuel Fittings, sight guages
|
Details
|
|
|
02-23-2010
|
9.00
|
Fitted copilot wheel/gear well
|
Details
|
|
|
02-22-2010
|
10.00
|
Glass in bulkheads
|
Details
|
|
|
02-19-2010
|
8.00
|
Shape and cleanup bulkhead flanges
|
Details
|
|
|
02-18-2010
|
8.00
|
Built Flanges for bulkheads
|
Details
|
|
|
02-17-2010
|
8.00
|
Cutting and installing copilot wheelwell
|
Details
|
|
|
02-16-2010
|
8.00
|
Fitting copilot wheel well
|
Details
|
|
|
02-15-2010
|
8.00
|
Copilot Wheel Well
|
Details
|
|
|
02-12-2010
|
8.00
|
Strake baggage area bulkheads
|
Details
|
|
|
02-11-2010
|
6.00
|
Fuel System Baffles
|
Details
|
|
|
01-28-2010
|
9.00
|
Bulkhead fitting
|
Details
|
|
|
01-27-2010
|
8.00
|
Install bulkheads
|
Details
|
|
|
01-26-2010
|
8.50
|
Fitting Bulkheads
|
Details
|
|
|
01-25-2010
|
6.50
|
Form flange for wheel well
|
Details
|
|
|
01-18-2010
|
8.00
|
Modify wheel well
|
Details
|
|
|
01-15-2010
|
8.00
|
Fit wheel wells and mod wheel well
|
Details
|
|
|
01-14-2010
|
9.00
|
Cutting well to fit gear
|
Details
|
|
|
01-13-2010
|
9.00
|
Cut gear well holes
|
Details
|
|
|
01-12-2010
|
4.50
|
Cut gear holes in lower strake
|
Details
|
|
|
01-12-2010
|
3.00
|
Adjust tow-in of tires
|
Details
|
|
|
|
01-11-2010
|
6.00
|
Glass in lower strake
|
Details
|
|
|
01-04-2010
|
4.50
|
Adhere Lower Strake to Main Spar
|
Details
|
|
|
12-31-2009
|
5.50
|
Final fit of lower strakes
|
Details
|
|
|
12-30-2009
|
6.00
|
Glass aft part of lower strake
|
Details
|
|
|
12-29-2009
|
7.50
|
Hang wings, fit lower strakes
|
Details
|
|
|
12-28-2009
|
8.00
|
Prepare fuselage and strakes
|
Details
|
|
|
12-09-2009
|
8.00
|
Fuselage prep for strakes
|
Details
|
|
|
12-08-2009
|
4.00
|
Lower Strake alignment
|
Details
|
|
|
12-08-2009
|
3.50
|
Cut out Strake bulkheads
|
Details
|
|
|
12-07-2009
|
5.00
|
Install Oil cooler duct and fresh air scoop
|
Details
|
|
|
12-07-2009
|
2.00
|
Install new gas springs
|
Details
|
|
|
|
12-04-2009
|
8.00
|
Oil cooler duct
|
Details
|
|
|
12-03-2009
|
8.00
|
Install Oil cooler and Fresh air vent
|
Details
|
|
|
12-02-2009
|
8.00
|
Nose Cooler Duct
|
Details
|
|
|
12-01-2009
|
7.00
|
Fit Doors
|
Details
|
|
|
|
11-30-2009
|
8.00
|
Install Door Gas Springs
|
Details
|
|
|
11-20-2009
|
8.00
|
Install door gas springs
|
Details
|
|
|
11-19-2009
|
7.00
|
Fit Doors
|
Details
|
|
|
11-17-2009
|
4.00
|
Window Protection
|
Details
|
|
|
|
11-17-2009
|
4.00
|
Fit Doors
|
Details
|
|
|
11-16-2009
|
0.00
|
Service Center Workplace setup
|
Details
|
|
|
11-11-2009
|
0.00
|
Move to Sebastian
|
Details
|
|
|
10-10-2009
|
1.00
|
Glass in Oil cooler Nose NACA scoop
|
Details
|
|
|
10-09-2009
|
6.00
|
Flapper valve for oil cooler
|
Details
|
|
|
10-08-2009
|
5.00
|
Fabricate Flapper Valve for oil cooler
|
Details
|
|
|
10-07-2009
|
1.50
|
Install Hydraulic Pump
|
Details
|
|
|
10-06-2009
|
4.00
|
Install Gear Contol system
|
Details
|
|
|
10-05-2009
|
6.00
|
Install gear contol system
|
Details
|
|
|
08-28-2009
|
1.00
|
Install Battery Shelf
|
Details
|
|
|
|
08-27-2009
|
5.00
|
Build Battery Tray
|
Details
|
|
|
08-09-2009
|
1.00
|
Build Battery Tray
|
Details
|
|
|
08-07-2009
|
5.00
|
Rudder Pedal/Toe Brake
|
Details
|
|
|
08-03-2009
|
5.50
|
Rudder Pedal/Toe Brake
|
Details
|
|
|
07-26-2009
|
2.00
|
Nose Gear Guides finished
|
Details
|
|
|
07-25-2009
|
5.00
|
Glass in Nose Gear Guides
|
Details
|
|
|
07-24-2009
|
7.00
|
Nose gear guides
|
Details
|
|
|
07-23-2009
|
5.50
|
Prepare Nose Gear Guides
|
Details
|
|
|
|
07-23-2009
|
1.50
|
Glassed MG bushing on firewall
|
Details
|
|
|
07-22-2009
|
2.00
|
Rudder Pedal/Toe Brake
|
Details
|
|
|
07-21-2009
|
5.00
|
Rudder Pedal/Toe Brke
|
Details
|
|
|
05-14-2009
|
7.00
|
Mount nutplates on fuselage tabs and canard
|
Details
|
|
|
05-12-2009
|
3.50
|
Trim Canard and fuselage tabs
|
Details
|
|
|
05-07-2009
|
3.50
|
Fuselage tabs for Canard attachment
|
Details
|
|
|
05-06-2009
|
3.50
|
Fuselage attach tabs for Canard
|
Details
|
|
|
04-24-2009
|
6.00
|
Build canard attach points.
|
Details
|
|
|
11-04-2008
|
7.50
|
Fuselage edge treatment for doghouse
|
Details
|
|
|
11-03-2008
|
4.50
|
Dog house edge treatment
|
Details
|
|
|
10-30-2008
|
5.00
|
Prepare MG pulley holes
|
Details
|
|
|
|
10-29-2008
|
8.00
|
Mount MG pulleys
|
Details
|
|
|
09-03-2008
|
6.50
|
Cut holes for gear legs
|
Details
|
|
|
08-19-2008
|
7.00
|
MG Pulley instalation
|
Details
|
|
|
06-02-2008
|
5.50
|
Notch bulkheads for gear legs
|
Details
|
|
|
06-02-2008
|
2.00
|
Locating position for MG pulley system
|
Details
|
|
|
06-01-2008
|
2.00
|
Main Gear Knurled bushings.
|
Details
|
|
|
05-31-2008
|
6.00
|
Triax MG knurled bushings / build gear sockets
|
Details
|
|
|
05-30-2008
|
3.00
|
Fabricate Aluminum spacers for Main Gear
|
Details
|
|
|
05-29-2008
|
2.50
|
Grind top of gear legs make shims
|
Details
|
|
|
05-27-2008
|
8.00
|
Install main gear bushings
|
Details
|
|
|
05-18-2008
|
5.00
|
Glass in Transverse bulkhead
|
Details
|
|
|
05-17-2008
|
7.50
|
Build Transverse bulkheads
|
Details
|
|
|
05-15-2008
|
3.00
|
Enlarge hole for Pilot gear leg
|
Details
|
|
|
|
05-14-2008
|
4.00
|
Enlarging Pax side gear hole
|
Details
|
|
|
05-12-2008
|
4.00
|
Clean up gear bulkhead/firewall/spar reinforcement
|
Details
|
|
|
05-08-2008
|
6.00
|
Gear bulkhead/firewall/spar reinforcing
|
Details
|
|
|
05-07-2008
|
8.00
|
Gear bulkhead/Firewall/Main spar reinforcements
|
Details
|
|
|
04-25-2008
|
4.00
|
Glassing Main Spar in
|
Details
|
|
|
04-24-2008
|
6.00
|
Main (Center) Spar Installatin
|
Details
|
|
|
04-23-2008
|
8.00
|
Level Airplane
|
Details
|
|
|
02-09-2008
|
2.00
|
Lower aileron torque tube
|
Details
|
|
|
02-06-2008
|
3.50
|
Lower Aileron torque tube
|
Details
|
|
|
|
02-05-2008
|
3.00
|
Lower Aileron torque tube
|
Details
|
|
|
01-29-2008
|
5.00
|
Lower Aileron Torque tube
|
Details
|
|
|
|
11-28-2007
|
0.00
|
"Hangar" setup
|
Details
|
|
|
10-13-2007
|
0.00
|
Aircraft Delivery
|
Details
|
|
|
10-06-2007
|
1.00
|
Trim canard mod for air intrusion
|
Details
|
|
|
|
10-06-2007
|
1.50
|
Clean up NG hinge tabs
|
Details
|
|
|
|
10-05-2007
|
2.50
|
Reinforce nose gear tabs
|
Details
|
|
|
10-05-2007
|
3.00
|
Drill hole in fuselage for torque tube
|
Details
|
|
|
|
10-05-2007
|
0.50
|
Cut nose gear door into 2 halves
|
Details
|
|
|
10-05-2007
|
1.50
|
Cut fuselage for main spar
|
Details
|
|
|
|
10-04-2007
|
3.00
|
Install nose gear doors
|
Details
|
|
|
10-04-2007
|
1.50
|
Install NG captivator
|
Details
|
|
|
10-04-2007
|
3.00
|
Install Canard
|
Details
|
|
|
10-04-2007
|
2.00
|
Glass end rib on canard tips
|
Details
|
|
|
10-03-2007
|
3.00
|
Prepare Nose gear door
|
Details
|
|
|
10-03-2007
|
1.50
|
Prepare canard for installation
|
|
|
|
10-03-2007
|
2.00
|
Install overcenter linkage
|
Details
|
|
|
10-03-2007
|
4.00
|
Install canard wing tips
|
Details
|
|
|
|
10-02-2007
|
2.50
|
Installed elevator counterweights
|
Details
|
|
|
|
10-02-2007
|
3.00
|
Install nose gear
|
Details
|
|
|
10-02-2007
|
2.00
|
Glass fuel baffle material
|
Details
|
|
|
10-02-2007
|
0.50
|
Cut canard bulkhead slot for Nose Gear
|
Details
|
|
|
10-01-2007
|
3.00
|
Install Canard hinge arms and center hinge
|
Details
|
|
|
10-01-2007
|
2.50
|
Canard attachment reinforcement
|
Details
|
|
|
09-28-2007
|
2.50
|
Keel stiffening layups
|
Details
|
|
|
09-28-2007
|
1.00
|
Install nut plates for keel NG access
|
Details
|
|
|
09-28-2007
|
1.50
|
Fabricate oil cooler duct
|
Details
|
|
|
09-27-2007
|
2.50
|
Install MG & NG Hydraulic cylinders
|
Details
|
|
|
09-27-2007
|
1.50
|
Install Keel
|
Details
|
|
|
09-27-2007
|
2.50
|
Install elevator hinges
|
Details
|
|
|
09-27-2007
|
2.50
|
Install Canard hinge arms
|
Details
|
|
|
09-26-2007
|
1.50
|
Prepare for Engine cooling NACA scoops
|
Details
|
|
|
09-26-2007
|
1.50
|
Install oil cooler NACA scoop
|
Details
|
|
|
09-26-2007
|
1.00
|
Install Marker Beacon Antenna
|
Details
|
|
|
09-26-2007
|
2.00
|
Glue Engine cooling NACA ducts in
|
Details
|
|
|
09-26-2007
|
1.00
|
Glass Nose gear access hole in keel
|
Details
|
|
|
09-26-2007
|
0.50
|
Cut hole for oil cooler NACA duct
|
Details
|
|
|
09-25-2007
|
2.00
|
Keel nose gear access hole
|
Details
|
|
|
09-25-2007
|
0.50
|
Install upper aileron torque tube
|
|
|
|
09-25-2007
|
2.00
|
Install lower Aileron torque tube
|
Details
|
|
|
09-25-2007
|
0.50
|
Drill control stick access holes
|
Details
|
|
|
09-25-2007
|
1.00
|
Cut out landing light and nose gear holes.
|
Details
|
|
|
09-25-2007
|
4.00
|
Cut engine cooling and fresh air NACA scoop holes
|
Details
|
|
|
09-24-2007
|
1.00
|
Remove Keel from fast Build Fuselage
|
Details
|
|
|
09-24-2007
|
2.00
|
Glass wooden hard points onto keel
|
Details
|
|
|
09-24-2007
|
1.50
|
Front Aileron Torque tube
|
Details
|
|
|
09-24-2007
|
0.50
|
Cut out nose access cover
|
Details
|
|
|
09-24-2007
|
2.50
|
Cut out dog house
|
Details
|
|
